User manual WHIRLPOOL EKIO 7640 IN INSTRUCTION FOR USE

[. . . ] - Do not pull the appliance’s power cable. - The electrical parts must not be accessible to the user after installation. - The appliance is designed solely for domestic use for cooking food. The Manufacturer declines any liability for inappropriate use or incorrect setting of the controls. [. . . ] • Only use flat-bottomed pots and pans. • When possible, keep pot lids on during cooking. • Use a pressure cooker to to save even more energy and time. • Place the pot in the middle of the cooking zone marked on the hob. DECLARATION OF CONFORMITY This appliance, intended to come into contact with food products, complies with Regulation ( ) no. 1935/2004, and has been designed, manufactured and marketed in conformity with the safety requirements of “Low Voltage” Directive 2006/95/EC (replacing 73/23/EEC as amended) and protection requirements of “EMC” Directive 2004/108/EC. BEFORE USE IMPORTANT: The cooking zones will not switch on if pots are not the right size. Only use pots bearing the symbol “INDUCTION SYSTEM” (Figure opposite). Place the pot on the required cooking zone before switching the hob on. EXISTING POTS AND PANS OK NO Use a magnet to check if the pot is suitable for the induction hob: pots and pans are unsuitable if not magnetically detectable. - Make sure pots have a smooth bottom, otherwise they could scratch the hob. - Never place hot pots or pans on the surface of the hob’s control panel. This could result in damage. RECOMMENDED POT BOTTOM WIDTHS Ø XL 28 cm 17 cm Ø 28 cm M Ø 18 cm 12 cm Ø 18 cm Ø L 21 cm 15 cm Ø 21 cm S Ø 14, 5 cm 16 cm 10 cm Ø 14, 5 cm 16 cm Max. Min. Ø 12 cm 18 x 23 cm 18 cm 23 cm EN12 INSTALLATION After unpacking the product, check for any damage during transport. In case of problems, contact the dealer or the After-Sales Service. PREPARING THE CABINET FOR FITTING WARNING • • • - The lower part of the product must not be accessible after installation. In case of installation of an undertop oven, do not interpose the separator panel. In order to ensure the correct operation of the product, do not obstruct the minimum required clearance between the hob and the top of the unit (min. If an oven is installed beneath the hob, make sure the oven is equipped with a cooling system. To remove the hob from the worktop use a screw driver (not supplied) unlocking the springs from the bottom side of the appliance. ELECTRICAL CONNECTION Disconnect the appliance from the power supply. Installation must be carried out by qualified personnel who know the current safety and installation regulations. The manufacturer declines all liability for injury to persons or animals and for damage to property resulting from failure to observe the regulations provided in this chapter. Make sure the voltage specified on the dataplate located on the bottom of the appliance is the same as that of the home. WARNING - - Electrical connections Important!• Electrical connection must be made before connecting the oven to the electricity supply. • For electrical connection, refer exclusively to the instructions given in the following paragraph, ignoring the connections indicated on the underside of the hob. Connection to the oven WARNING Do not connect the oven to the power supply before you have finished connecting the cooktop. • Before connecting the oven to the power supply, make sure that the cooktop is among the ones listed in the cooktop/oven pairing product sheet provided. • Connect the hob connectors (E) to the oven connectors (D), matching the colours and the alignment of the housing guides visible on the top of the connectors. [. . . ] • Use a soft cloth, absorbent kitchen paper or a specific hob cleaner (follow the Manufacturer’s instructions). WARNING - TROUBLESHOOTING GUIDE • • • Read and follow the instructions given in the section “Instructions for use”. Dry the hob thoroughly after cleaning it. EN14 AFTER-SALES SERVICE Before contacting the After-sales Service: 1. See if you can solve the problem yourself with the help of the “Troubleshooting guide”. Switch the appliance off and then on again it to see if the problem has been eliminated. [. . . ]