User manual WHIRLPOOL ETN 5240 IN PROGRAM CHART

[. . . ] This appliance is marked according to the European directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE). By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health. The symbol on the product, or on the documents accompanying the product, indicates that this appliance may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. [. . . ] Acid substances such as lemon juice, tomato, vinegar or similar, make the surface opaque if not removed for a long time. Enamelled parts must be cleaned with a sponge soaked in soapy water or other suitable non-abrasive products. Acid substances such as lemon juice, tomato, vinegar or similar, make the surface opaque if not removed for a long time. WARNINGS • • • Never operate the hotplates under no load (without recipients). Avoid whenever possible spillage of liquids on the hotplates when still warm. The hob is designed exclusively for domestic use to cook food. The manufacturer declines all liability for inappropriate use or incorrect settings of controls. Avoid exposure of the hob to atmospheric agents. Any repairs or operations must be performed exclusively by an authorised technician. ENAMELLED TOPS • • • • • Type PLATD 400 V~ 50 Hz 3, 5 kW 5019 419 01002 To get full satisfaction from the hob, please read these instructions carefully and keep them for future consultation. TROUBLESHOOTING GUIDE The hob does not work: - Check for the presence of mains electrical power. - Set the knob to “0” and switch on the hob again to ensure that the fault has been remedied. AFTER-SALES SERVICE Before contacting After-Sales Service: • See if you can solve the problem yourself with the help of the suggestions given in chapter “Troubleshooting Guide”. If after the above checks the fault persists, contact the nearest After-sales Service. Please give: • a brief description of the fault; • the type and exact model of the hob; • the service number (i. e. , the number that follows the word SERVICE on the rating plate, located under the hob). The service number is also indicated on the warranty booklet; • your full address; • your telephone number and area code. If any repairs are required, please contact an authorised After-sales Service (to guarantee that original spare parts will be used and repairs carried out correctly). Failure to comply with these instructions may compromise the safety and quality of the product. Connection to the electrical mains Note: the yellow/green earthing wire (B) must be connected to the screw. If the power cable is not yet connected: • strip approx. 70 mm of sheath from the power supply cable • strip approx. 10 mm of sheath from the wires • Open the terminal board (C) by pressing the side tabs by means of a suitable tool. • Insert the power cable (D) in clamp (E) and connect the wires to the terminal board. • After the electrical connection, insert the hob from the above and secure on the fixing brackets as shown in figure 1. Declaration of conformity • This cooking hob is suitable for contact with foodstuffs, and complies with EEC Directive 89/109. • This cooking hob has been designed to be used only for cooking Any other use (such as heating a room) is improper and dangerous • This cooking hob has been designed, constructed and marketed in compliance with: - safety requirements of EEC Directive “Low voltage” 73/23; - protection requirements of EEC Directive “EMC” 89/336; - requirements of EEC Directive 93/68. The hob does not turn off: - disconnect the hob immediately by disconnecting the power cable from the socket. ACCESSORIES: • The glass cover can be ordered via the After Sales Service, with the code: AMC 966 NB (New Black) AMC 966 MR (Mirror) INSTALLATION Recommendations Important: Before any installation or maintenance operation, disconnect the hob from the mains power supply. • Electrical connections must be made before connecting the appliance to the electricity supply. • Installation must be performed by a qualified technician according to the manufacturer's instructions and current local regulations. [. . . ] If the hob is to be installed next to a column unit, leave a distance of at least 100 mm from the edge hob. Make an opening in the worktop, observing the dimensions specified. Fit the seal supplied onto the hob (if not already present), after carefully cleaning the application surface. Fig. 1 • • • • • • • Electrical connection • • • • • • Regulations require that the appliance is earthed. [. . . ]