User manual WHIRLPOOL ETPI 8930/IN PROGRAM CHART

[. . . ] 41901130. book Page 12 Thursday, September 10, 2009 12:01 PM ENGLISH Installation Page 2 Instructions for use Page IMPORTANT SAFETY INFORMATION YOUR SAFETY AND THE SAFETY OF OTHERS ARE VERY IMPORTANT This manual and the appliance itself provide important safety messages, to be read and observed at all times. This is the safety alert symbol, pertaining to safety, which alerts users to potential hazards to themselves and others. All safety messages will follow the safety alert symbol and either the terms: DANGER WARNING Indicates a hazardous situation which, if not avoided, will cause serious injury. Indicates a hazardous situation which, if not avoided, could cause serious injury. All safety messages tell you what the potential hazard is, how to reduce the risk of injury, damages and electrical shocks resulting from the incorrect use of the appliance. Please observe the following instructions: - The appliance must be disconnected from the power supply before carrying out any installation work. [. . . ] The appliance must be installed by a qualified technician who is fully aware of current safety and installation regulations. The manufacturer declines all liability for injury to persons or animals and for damage to property resulting from failure to observe the regulations provided in this chapter. The power supply cable must be long enough to allow the hob to be removed from the worktop. Make sure the voltage specified on the appliance rating plate is the same as that of the house electrical system. Do not use extension leads. WARNING - - Connecting to the terminal board For electrical connection, use an H05RR-F cable as specified in the table below. Conductors 230 V ~ + 230-240 V ~ + 230 V 3 ~ + 400 V 3N ~ + 400 V 2N ~ + Amount x size 3 x 4 mm2 3 X 4 mm2 (Australia only) 4 X 1. 5 mm2 5 X 1. 5 mm2 4 X 1. 5 mm2 400 V 3N ~ 230 V ~ 230-240 V ~ (Australia only) 230 V ~ (UK only) 230 V 230 V 230 V 230 V 400 V 2N ~ 230 V 3 ~ (Belgium only) 400 V 2N ~ (NL only) A B C 230 V 230 V 230 V 230 V 230 V 230 V Connect the yellow/green earth wire to the terminal with the symbol . This wire must be longer than the other wires. Remove the terminal block cover (A), undoing the screw and inserting the cover in the terminal block hinge (B). 70 mm of sheath from the power supply cable. Insert the power supply cable into the cable clamp and connect the wires to the terminal board as indicated in the diagram next to the terminal board itself. Secure the power cable with the cable clamp. Close the cover (C) and screw it on the terminal block with the removed screw - point (1). Each time the cooktop is connected to the mains it carries out an automatic check which lasts several seconds. If the hob already has a power cable, follow the instructions given on the label attached to the cable. Connect to the power mains using a multi-pole power switch with a contact gap of at least 3 mm. GB14 230 V 41901130. book Page 15 Thursday, September 10, 2009 12:01 PM INSTRUCTIONS FOR USE Control Panel Description The control panel is equipped with touch controls: to use them, just press the corresponding symbol (it is not necessary to press hard). To select and activate the cooking zones To set the minute counter Hob ON/OFF To select one of the automatic functions Slide touch screen To enable the hold function To lock the control panel First use / after a power failure After connecting the hob to the electrical power supply, the control panel is locked (the indicator light above the key is ON). To unlock the control panel, press and hold the key for 3 seconds. The indicator light switches off and the hob can be used normally. Switching the hob ON/OFF To switch the hob on, press and hold the key for approx. 2 seconds: the indicator light above the key turns on and hyphens appear inside the cooking zone circles. To switch off, press the same key until the hob switches off. All the cooking zones are switched off. i The hob automatically switches off if no function is selected within 10 seconds of switching on. Switching on and adjusting cooking zones Cooking zone selection and selected cooking zone/power level display Indicates that one of the automatic functions is On Cooking zone timer Slide touchscreen (power adjustment) After switching on the hob, position the pot on the chosen cooking zone. Activate the cooking zone by pressing the relative round key: the round key displays number 5 that corresponds to the intermediate power level. The hob automatically switches off if no function is selected within 10 seconds of switching on. [. . . ] • Use a soft cloth, absorbent kitchen wipes or a specific hob cleaner (follow the Manufacturer's instructions). WARNING - TROUBLESHOOTING GUIDE • • • • • Read and follow the instructions given in the section “Instructions for use”. Connect the hob to the electricity supply and check that the supply has not been shut off. If you are unable to turn the hob off after using it, disconnect it from the power supply. If, when the hob is switched on, alphanumeric codes appear on the display, consult the following table for instructions. ERROR CODE DESCRIPTION POSSIBLE CAUSES Water or utensils on control panel. REMEDY Clean the control panel. [. . . ]