User manual WHIRLPOOL EV 1049 PRODUCT FICHE

[. . . ] Only woollens with a felt-free finish, labelled with the woolmark and identified as machine washable. Textiles made of linen, silk, wool and viscose marked as “handwashable”. Same as the last rinse and the final spin in the “Cotton” programme. In this programme spinning is intensive. [. . . ] Drain only - no spinning. – – – – – – – Yes Yes Yes – – – – i i i i – – – i 2) i 2) i 2) i i i i – – – – – – – i i i – – – – i i i i i i – 1000 1000 400 3) 1000 1000 1000 – N. B. Please avoid excessive detergent dosing. Laden is a registered trademark of Whirlpool USA. 5019 612 10116 CONSUMPTION DATA Temperature Programme Cotton Cotton** Cotton Synthetics Synthetics Delicates Daily load Quick wash Wool Handwash (°C) 95 60 40 60 40 40 40 30 40 40 (kg) 5. 0 5. 0 5. 0 2. 5 2. 5 1. 5 3. 0 3. 0 1. 0 1. 0 (l) 50* 49 55 50* 45 50 40 35 55 40 (kWh) 1. 70 0. 95 0. 55 0. 80 0. 45 0. 55 0. 45 0. 40 0. 55 0. 40 Load Water Energy Approx. Programme Duration (hours : minutes) 2:05 2:10 2:00 1:30 1:15 0:45 1:00 0:30 0:45 0:35 Prewash cycle increases programme duration by aproximately 20 min. Consumption values were measured in normalized conditions in compliance with standard IEC/EN 60 456. Consumption data in the home may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash. * To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out. ** Reference Programme for Energy Label. PREPARATION OF THE WASH CYCLE 1. Load the machine, close the drum doors and check that they are properly locked. Add detergent and additives into the dispenser to no more than the “MAX” level mark, as follows: • Programme with pre and main wash • Main wash programme without prewash • Fabric softeners and conditioners • Stain remover agents • Anti-scale agents (if necessary) 3. Turn the programme selector to the desired programme and temperature. The lamp next to the “Start/Pause” button flashes. SELECT THE DESIRED OPTION(S) Selecting or deselecting an option can be done at any time during the programme. The indication lamp next to the “Start/Pause” button lights up. The programme sequence indicator shows the current programme phase, running from left to right through Wash, Rinse, Spin/Drain. When the programme phrase is finised, the corresponding indication goes out. • Note: If there is a power interruption or if the appliance is disconnected during the cycle, the programme will run again from the point where it was interrupted. “DOOR OPEN” INDICATION Before starting and after end of a programme, the lamp lights to show the the lid can be opened. As long as a wash programme is running, the lid remains locked and must on no account be forced open. In case you have an urgent need to open it during a running programme, refer to “Cancel (Reset) a running programme before the end”. RED INDICATIONS “Service” Lighting up of the “Service” indication can be caused by a fault in an electrical component. Refer to the “Troubleshooting Guide” in your “Instructions for Use”; if the fault persists, contact our After Sales Service. “Water tap closed” The appliance has no or insufficient water supply. Open the water tap: if the indications still lights up, refer to the “Troubleshooting Guide” in the Instructions for Use. “Clean pump” Waste water is not pumped out. [. . . ] PROGRAMME END • All the lights of the programme sequence indicator are off, and the “Door open” indication lights up. Turn the programme selector to the “Off/O” position. Open lid and drum and unload the machine. Leave the lid open for some time to allow the interior of the machine to dry. [. . . ]