User manual WHIRLPOOL GSIP 6143/1 A IN PRODUCT FICHE

[. . . ] • This dishwasher has been factory tested to ensure it functions correctly. Such testing may leave slight water marks that will disappear with the first wash. Water and electrical connections: All water and electrical connections must be carried out by a qualified technician in compliance with the manufacturer's instructions (refer to the enclosed installation booklet) and current local safety regulations. The appliance must only be used in the household for the prescribed uses. [. . . ] Refer to the “Connections” chapter in these user instructions. Disposal: The appliance is built from reusable materials. If you decide to scrap the dishwasher, it must be disposed of in compliance with local waste disposal laws. Before scrapping, cut off the power cable so that the appliance cannot be connected to the mains. • To prevent situations of potential danger to children (e. g. danger of suffocation), break the lock of the door so that it can no longer be closed. Child safety: • Children must not be allowed to play with the dishwasher. • Store the detergent, rinse aid and salt in a dry place out of the reach of children. Safety warnings: • The open dishwasher door can only support the weight of the loaded rack when pulled out. Do not rest objects on the open door or sit or stand on it: the appliance may topple over!• Do not use solvents inside the dishwasher: risk of explosion!If the water hardness level does not correspond to position 3 (factory setting) or if the water hardness level changes: Set the water hardness level (for dishwashers without water hardness sensor only): Setting must be carried out according to the following table. • Switch on the appliance (consult the quick reference guide). • Select programme 2 (consult the programme chart in the quick reference guide). • Press the Start button for at least 5 seconds until the Start indicator lamp blinks. • The “Start indicator lamp” blinks or the digital display lights up according to the water hardness level selected (chart, setting - blinking frequency or digital display). • With each successive touch of the Start button the setting increases and when it reaches 7 it returns to 1 again. • Switch off the appliance (consult the quick reference guide). The selected setting is now memorized. Hardness level German degrees °dH French degrees °fH mmol/l Clarke scale or English degrees °eH Setting blinking frequency (1x-7x) or digital display (1-7) Settings for dishwashers without water hardness sensor only. In appliances provided with a water hardness sensor, the setting is automatically executed. 1 soft 1 - 2 medium 2 average 3 medium-hard 4 hard 4 very hard 4 extremely hard 0-5 6 - 10 11 - 15 16 - 21 22 - 28 29 - 35 36 - 60 0-9 10 - 18 19 - 27 28 - 37 38 - 50 51 - 63 64 - 107 0 - 0. 9 1. 0 - 1. 8 1. 9 - 2. 7 2. 8 - 3. 7 3. 8 - 5. 0 5. 1 - 6. 3 6. 4 - 10. 7 0 - 6. 3 7 - 12. 6 13. 3 - 18. 9 19. 6 - 25. 9 26. 6 - 35 35. 7 - 44. 1 44. 8 - 74. 9 1x 2x 3x 4x 5x 6x 7x 1 2 3 4 5 6 7 If the water hardness level falls within category 1 (soft), no salt is required. How to fill the salt container Warning: Only use regeneration salts for use in domestic dishwashers!Do not fill the salt container with unsuitable substances, such as detergent, as this will cause irreparable damage to the water softener system. Unscrew the cap by turning it counter-clockwise. [. . . ] This prevents the formation of excess suds which may spoil washing results. Thereafter, regularly check the rinse aid level. A How to adjust the rinse aid dosage regulator Factory setting: Position 4. If you are not satisfied with washing or drying results, change the rinse aid dosage setting. Press button A to open the cover (see drawing). [. . . ]