User manual WHIRLPOOL GSXK 2990 WP INSTRUCTION FOR USE

[. . . ] Warning: when the door is opened steam comes out!Unload the appliance, starting from the lower rack. Switch off the appliance Turn off the water tap, unload the racks Dishwasher loading instructions and racks provided Upper rack: Multi-purpose support (A): 1) Depending on the position, for longhandles utensils, cups and glasses. May be used in three different positions. Crockery holders (B): Depending on the position, for example plates, cups and long-stemmed glasses. [. . . ] carving forks, knives) must be arranged with the sharp end facing in towards the appliance. depending on the model Half Load: Load the upper rack (see description of Options). Place the cutlery basket (D) in the upper rack. Rack height adjustment (also when loaded): • Lower adjustment: pull out the two rack handles outwards (E) and lower the rack. • Upper adjustment: pull the two handles (E) upwards until the rack clicks into place (Factory setting). Removing the top rack to provide clearance for large items of crockery in the bottom rack: Open the rack guide retainers (F) on the right and left and remove the top rack. When the upper rack is in place the retainers must always be closed. Retainer closed Retainer open F Lower rack: Depending on the model with fixed, tilting (G) or tilting split plate holders (H). Half Load: Load the lower rack (see description of Options). Greater washing power, particularly for plates and saucepans. F I Power Clean load Increased wash power in the dedicated area (I) and high flexibility for lower rack loading. H Cutlery basket (J) or (L): Some models are provided with a grid (K) that can be fitted onto the cutlery basket to keep items separated. Cutlery basket (D), if provided, for appliances with half load only. Sharp knives and forks that might cause injury must be placed in the cutlery basket with the sharp end facing downwards. Only use dishwasher-proof crockery and dishes. Do not use the appliance for items not suitable for washing in a dishwasher, for example wooden items, aluminium, plastic utensils, tin, hand-decorated crockery (unglazed), silver cutlery. not sparkling Rust on cutlery Identifying appliance faults • Not made of stainless steel. • The START indicator lamp flashes. (if provided). • Use suitable glasses. • Use suitable cutlery. • Ensure the filter assembly is not clogged and that there is no interruption to the water supply (if necessary, clean the filters *). Press the START button for 2 seconds, until the START indicator lamp switches off. Select a new programme and press the Start button again. If, after carrying out the above checks, the fault persists, switch off the appliance, disconnect the mains plug and turn off the water tap. Contact the After-Sales Service (see warranty). Before contacting our After-Sales Service, take note of the following: • The nature of the fault • The appliance type and model • The service code (the number indicated on the adhesive rating plate) inside the door on the right-hand side. Before using the dishwasher, read the user instructions! GSXK 2990 WP Quick Reference Guide Options 3) Time and failure display GB On button Off button Programme selection button The selected programme is shown in the window of the display. Indicates in hours the time remaining until the start of the wash cycle. Switches off when the programme starts and indicates the time remaining in hours and minutes. “F. . . . ” Identification of faults for service technician “Delayed start” button Start button Switches “on” when the dishwasher is operating. Switches off at the end of the programme. The wash cycle can be programmed to start after 1 - 24 hours. [. . . ] With each successive touch of the button, the delayed start indicator increases by 1 hour, and after 24 returns to 00. The dishwasher will start at the set time. “Half load - Multizone” button After pressing the Reset button, the selected programme and the supplementary functions are cancelled (except the detergent and water hardness settings, see user instructions) and must be reset. On releasing the button this is confirmed by an acoustic signal. Reset button Load the upper or lower rack only. This function can be used with any programme. [. . . ]