User manual WHIRLPOOL HANNOVER 1400 PROGRAM CHART

[. . . ] Normally soiled blouses, shirts and other outer clothing made of polyester (Diolen, Trevira), polyamide (Perlon, Nylon) or mixtures of these fibres with cotton. E G H Programme Care Labels Max. Detergent and Additives Selectable Special Options = ❉ load Softener Main Pre- Start Eco Pre- Intensive Rinse Variable wash wash Delay wash Rinse hold spin Start Eco Voor- Intensief Spoel- Centrif. kg selectie was Spoelen stop Cotton Bonte was 6. 0 ❉ Yes ❉ ❉ ❉ ❉ ❉ Synthetic Synthetisch 2. 5 ❉ ❉ ❉ ❉ ❉ ❉ ❉ Yes ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ Daily mixed Rapid wash Delicate Wool Handwash / Lingerie Easy ironing Gemengde was Snelwas Fijne was Wol Handwas / Lingerie 3. 0 3. 0 1. 5 1. 0 1. 0 Yes Yes Yes Yes Yes – – ❉ – – – – – ❉ – – ❉ – – – – ❉ – – ❉ – – ❉ Makkelijk strijken 3. 0 Yes Spin Rinse & Spin Centrifugeren Spoelen & Centrifugeren – – – – – – 6. 0 6. 0 – ❉ – – – – – – – – – – – – – ❉ Drain 1) 2) Afpompen – – – For improved garment care spin speed is restricted to 1000 rpm in this programme. For improved garment care spin speed is restricted to 400 rpm in this programme. Black process 45. 0° 100. 0 LPI { ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ F I G. [. . . ] Turn on the tap and start the programme by pressing the “Start” button. Now the indicator light above the button goes on. In addition, all programme phases are indicated by the associated lights. After the end of a programme phase, the associated indicator light goes out. Thus the programme sequence indicator moves from left to right across the wash, rinse and spin phases. At the end of the programme, only the “End” indicator is still on. . “DOOR LOCKED” INDICATOR As long as a washing programme is running, the lamp lights up to show that the door cannot be opened. When the lamp goes off, the door can be opened again. If “Start” has been pressed, but the door is not latched, the “Door Locked” indicator flashes for 10 seconds. The door must be pushed shut within this time. After the 10 seconds, the “Door Locked” indicator goes out and the “Start” button flashes. The door must then be opened and closed again and the “Start” button must be pressed. “TROUBLE” INDICATORS “Pump” Waste water is not pumped out. Check wether the drain hose is kinked or the filter must be cleaned; in the latter case refer to the Instructions for Use (“Removing the Filter”). “Water tap closed” The appliance has no or insufficient water supply. Open the water tap; if the indication still lights up, refer to the “Troubleshooting Guide” in the Instructions for Use. PROGRAMME END • The “End” indicator goes on. Set the programme selector knob to the “Off” position. RESELECT AFTER PROGRAMME START A newly-selected programme will continue in the same programme section during which the current programme was interrupted. Therefore do not add any more detergent. Press the “Start” button to interrupt the programme. Select the new programme (with temperature), any additional options and - if you wish - another spin speed. Press the “Start” button again to restart the programme. [. . . ] • This option is particularly recommended for the programme “Synthetic” or “Delicate”. • This function is particularly useful if you want to postpone spinning to a later time. Note: The programme has reached the “Rinse Hold” when the corresponding light flashes. Terminate the “Rinse Hold” option: • Press the “Rinse Hold” button again; the programme will terminate automatically with the appropriate spin cycle for the current programme. [. . . ]