User manual WHIRLPOOL HB 433 S PROGRAM CHART

[. . . ] When the knobs are rotated, the LEDs light up progressively (from 1 to 6) to show the power selected. The hob is provided with 4 indicator lights showing when the cooking zones are hot. These indicator lights switch on as soon as the cooking zones reach a high temperature. These indicator lights remain on even after switching off of the relevant cooking zone and they switch off only when the temperature of the cooking zone is no longer dangerous. Important: To avoid permanently damaging the glass-ceramic top, do not use: - Pots with bottoms that are not perfectly flat. [. . . ] • Use a clean cloth, absorbent kitchen wipes and washing up liquid or a specific glass ceramic cleaner. • Remove baked-on dirt with the special scraper tool (if provided) and specific cleaning products. • Any food spills should be cleaned off before they dry. • Do not use abrasive products, chlorine-based cleaners, oven-cleaner spray or pan scourers. • The hob should be treated periodically with specific products available from the shops, following the manufacturer's instructions. DIMENSIONS OF THE COOKTOP AND WORKTOP (mm) CAUTION ELECTRICAL CONNECTION Supply voltage 230 V ~ Conductors Number x Size 3 X 2. 5 mm 2 • • • • Telescopic knobs (depending on model) • • The knobs can be lifted approx. After cleaning, restore the knob to its original position. - Make sure that the power supply is on. - Turn the hob off and on again, to make sure that the problem has been solved. - Make sure that the knob is not turned to “0”. Turn the multi-pole switch to “Off” for a few minutes and then turn it back to “On”. TROUBLESHOOTING GUIDE The hob does not work: • The hob will not switch off: - disconnect the hob immediately from the power supply. Type PLEVS 230V ~50Hz 5. 8 kW 5019 619 01050 To get full satisfaction from the hob, please read these instructions carefully and keep them for future consultation. AFTER SALES SERVICE Before you call the After Sales Service • Make sure that you cannot solve the problem yourself following the points described in chapter “Troubleshooting Guide“. If after the above checks the fault still occurs, get in touch with the nearest After Sales Service. Please give: • a short description of the fault; • the exact type and model of hob; service number (i. e. , the number that follows the word SERVICE on the rating plate under the hob itself). The service number is also indicated on the guarantee booklet; • your full address; • your telephone number. If any repairs are required, please contact an authorised After Sales Service (to guarantee that original spare parts will be used and repairs carried out correctly). Failure to comply with these instructions may compromise the safety and quality of the product. • Declaration of conformity • • This cooktop is suitable for contact with foodstuffs and complies with EEC (CE) Regulation n. This hob (Class Y) has been designed to be used only for cooking. Any other use (such as heating a room) is improper and dangerous. • This hob has been designed, constructed and marketed in compliance with: - safety objectives of the “Low Voltage” Directive 2006/ 95/CE (which replaces 73/23/CEE and subsequent amendments); - protection requirements of EEC Directive “EMC” 89/336; - requirements of EEC Directive 93/68. The Manufacturer reserves the right to change product specifications without prior notice. INSTALLATION Recommendations Important: Disconnect the hob from the mains before carrying out any installation work or servicing. • All electrical connections must be made before connecting the appliance to the power supply. • Installation must be carried out by a qualified technician in accordance with the manufacturer’s instructions and in compliance with local regulations. • Unpack the hob and make sure that the appliance has not been damaged during transport. If you are not sure contact the dealer or the nearest service centre. [. . . ] 1 • • • • • Connecting the oven to the power supply Fig. 3 Note: the yellow/green earth wire must be connected to the screw with the symbol . 70 mm of the cable sheath from the power supply cable (G). Insert the cable (G) through the opening in the lid (F). [. . . ]