User manual WHIRLPOOL HB D50 S INSTRUCTION FOR USE

[. . . ] • Clean the hob when it is cool, after each use. This will prevent the build-up of dirt and make cleaning easier. • Use a clean cloth, absorbent kitchen wipes and washing up liquid or a specific glass ceramic cleaner. • Clean stainless steel surface with a specific commercial product. [. . . ] This appliance is not intended for use by persons (including children) wit reduced physical, sensory or mental capabilities or lack of experiences and knowledge unless they have been given initial supervision or instruction concerning use of the appliance by a person responsible for their safety. After use, ensure that the knobs are in position “0”. Make sure that the electrical wires of other electrical appliances near the hob do not come into contact with hot parts. Always supervise cooking when using large quantities of grease or oil. Oil and grease can overheat and set fire!Do not use the hob surface as a support or work surface Never place plastic, aluminium foil, cloths, paper, etc. /cooking zones when still hot. DIMENSIONS OF COOKING HOB AND WORKTOP (mm) • • • • • • • • • • • • • Prolonged use of the hob may alter the colour of the glass ceramic surface due to the high temperatures reached. Acid substances such as lemon juice, tomato, vinegar or similar, make the surface opaque if not removed for a long time. Type PLAVD 230 V - 50 Hz 1. 3 kW 5019 619 01062 • To get full satisfaction from the hob, please read these instructions carefully and keep them for future consultation. TROUBLESHOOTING GUIDE The steak plate does not work: - Check for the presence of mains electrical power. - Set the knob to “0” and switch on the hob again to ensure that the fault has been remedied. AFTER-SALES SERVICE Before contacting After-Sales Service: • See if you can solve the problem yourself with the help of the suggestions given in chapter “Troubleshooting Guide”. If after the above checks the fault persists, contact the nearest After-sales Service. Please give: • a brief description of the fault; • the type and exact model of the hob; • the service number (i. e. , the number that follows the word SERVICE on the rating plate, located under the hob). The service number is also indicated on the warranty booklet; • your full address; • your telephone number and area code. If any repairs are required, please contact an authorised After-sales Service (to guarantee that original spare parts will be used and repairs carried out correctly). Failure to comply with these instructions may compromise the safety and quality of the product. Connection to the electrical mains Note: the yellow/green earthing wire (B) must be connected to the screw. If the power cable is not yet connected: • strip approx. 70 mm of sheath from the power supply cable • strip approx. 10 mm of sheath from the wires • open the terminal board (C) by pressing the side tabs by means of a suitable tool. • insert the power cable (D) in clamp (E) and connect the wires to the terminal board. • after the electrical connection, insert the hob from the above and secure on the fixing brackets as shown in figure 1. Declaration of conformity • This cooking hob is suitable for contact with foodstuffs, and complies with EEC Directive 89/109. • This cooking hob has been designed to be used only for cooking Any other use (such as heating a room) is improper and dangerous • This cooking hob has been designed, constructed and marketed in compliance with: - safety requirements of EEC Directive “Low voltage” 73/23; - protection requirements of EEC Directive “EMC” 89/336; - requirements of EEC Directive 93/68. The steak plate does not turn off: - disconnect the hob immediately by disconnecting the power cable from the socket. ACCESSORIES: • The glass cover can be ordered via the After Sales Service, with the code: AMC 966 NB (New Black) AMC 966 MR (Mirror). INSTALLATION Recommendations Important: Before any installation or maintenance operation, disconnect the steak plate from the mains power supply. • Electrical connections must be made before connecting the appliance to the electricity supply. • Installation must be performed by a qualified technician according to the manufacturer's instructions and current local regulations. [. . . ] If the steak plate is to be installed next to a column unit, leave a distance of at least 100 mm from the steak plate edge. Make an opening in the worktop, observing the dimensions specified. Fit the seal supplied onto the hob (if not already present), after carefully cleaning the application surface. Fig. 1 Electrical connection • • • • • • Regulations require that the appliance is earthed. [. . . ]