User manual WHIRLPOOL HJA1733 PROGRAM CHART

[. . . ] Installation & User’s Instructions HJA1733 Contents Introduction Welcome Safety symbols Important safety information Installation instructions Installation Electrical connection Operating Operating the hob Cooker care Care & maintenance Troubleshooting guide After-sales service 11 11 12 9 6 8 3 3 4 Safeguarding the environment 12 12 months guarantee 13 2 Introduction Welcome Dear customer Congratulations on your choice of a quality hob which has been designed to give you lasting service. The hob must be installed by a qualified electrician in accordance with current regulations and used in a well-ventilated space. Please read these instructions thoroughly before installing or using the appliance and keep them for handy reference. Make sure you understand the controls prior to using your appliance. [. . . ] Clean the cutout of any remaining dust that could compromise appliance operation. 6 Assembly 1. Position the clips (A) in the spaces provided on the hob trim (fig. Measure the centre point of the vertical sides of the cut-out (fig. Fit the brackets (C) in the centre of the vertical sides, aligning the upper edge of the brackets so that they are flush with the worktop surface (fig. Fix the brackets with the 4 screws supplied (B) using the holes provided. Insert the hob in the cutout, making sure the clips (A) are secured in the spaces provided (fig. 4). Undercounter hob installation • If an oven (which must be of our manufacture) is to be installed under the hob, ensure it is equipped with a cooling system and observe the distances given in the figure below. • There must be nothing between the cooktop and the hob (cross rails, panels, brackets, etc. ). 5 mm C B fig. 4 7 Electrical connection Electrical connections WARNING • Hob electrical connection must be made before connecting the appliance to the electricity supply. • Electrical connection must be carried out in compliance with the regulations of the local electric utility company. • Make sure that the voltage indicated on the rating plate on the underside of the appliance corresponds to the domestic power supply voltage. • Regulations require that the appliance is earthed: use conductors (including the earth conductor) of the appropriate size only. • For electrical connection, use an H05 RR-F type cable as specified in the table “Power supply voltage”. The power supply cable must be long enough to allow the hob to be removed from the worktop. Remove the terminal block cover (A), undoing the screw and inserting the cover in the terminal block hinge (B). 70 mm of sheath from the power supply cable. Insert the power supply cable into the cable clamp and connect the wires to the terminal board as indicated in the diagram next to the terminal board itself. Secure the power cable with the cable clamp. Close the cover (C) and screw it on the terminal block with the removed screw - point (1). Each time the cooktop is connected to the mains it carries out an automatic check which lasts several seconds. 400V 3N ~ 230V ~ 230-240V~FOR AU ONLY 230V~FOR UK ONLY 230V 230V 230V 230V Power supply voltage Wires 230V ~ + 230-240V ~ + 230V 3 ~ + 400V 3N ~ + 400V 2N ~ + Amount x size 3 X 4 mm2 230V 230V 400V 2N ~ 230V 3~ ONLY FOR BELGIUM 400V 2N~ FOR NL ONLY 4 X 1. 5 mm2 5 X 1. 5 mm2 4 x 1. 5 mm2 A 230V 230V B If the hob already has a power cable, follow the instructions given on the label attached to the cable. Connect the appliance to the electricity supply by means of an all-pole disconnect switch with minimum contact gap of 3 mm. C Connecting to the terminal board Connect the yellow/green earth wire to the terminal with the symbol . [. . . ] • Connect the hob to the electricity supply and check that the supply has not been shut off. • Clean the hob and dry it thoroughly. • If, when the hob is switched on, alphanumeric codes appear on the display, consult the following table for instructions. Error code Description Possible causes Water or utensils on control panel Remedy Clean the control panel The hob switches off Continuous pressure and after 30 seconds on control panel area emits an acoustic signal every 4 seconds C81, C82 The control panel The internal temperature of switches off because of electronic parts is too high excessively high temperatures The connection voltage is wrong Wait for the hob to cool down before using it again F42 or F43 The sensor detects a Disconnect the hob from discrepancy between the the mains and check the appliance voltage and that of electrical connection the mains supply F12, F21, F25, F36, F37, F40, F47, F56, F58, F60 Call the After-Sales Service and specify the error code 11 After-sales service Before contacting After-sales Service • Try to solve the problem (see “Troubleshooting guide”). • Switch the appliance off, wait 30 seconds then switch it on again to see if the fault persists. [. . . ]