User manual WHIRLPOOL KCDP 9010/I PROGRAM CHART

[. . . ] Note: always use gloves when installing or carrying out maintenance work. Electrical connection The mains voltage should correspond with the voltage shown on the specifications label found inside the hood. If there is no plug, connect the hood to a socket that complies with current legislation and is in an easily accessible location. If there is no plug (direct connection to the mains supply) or the plug is not in an easily accessible location, fit a legally complying bi-polar switch that ensures the complete disconnection of the mains in the event of a category III line surge, in compliance with the installation regulations. IMPORTANT: before reconnecting the hood circuit to the power supply, check that it is working properly, that the mains cable has been properly fitted and that it has NOT been crushed in its holder during installation. [. . . ] Follow the instructions in this manual carefully. All responsibility is denied for problems, damage or fire to the appliance resulting in failure to comply with the instructions in this manual. Extraction Modes The hood is designed to be used in two modes: Venting exhaust fumes to the outside, or by passing the air through a charcoal filter brfore recirculating the air back into the kitchen. Vented Mode The hood comes with an upper air outlet B for the discharge of fumes to the outside (vented exhaust pipe and fixing straps are not supplied). 1 Recirculation Mode If the fumes and steam from cooking cannot be discharged towards the outside, you can use the recirculation mode by fitting an activated carbon filter (not supplied, this must be purchased seperately) and the deflector F on the support (bracket) G; the fumes and steam are recirculated via the upper grid H and an exhaust pipe, connected to the upper air outlet B and the connection ring fitted to the deflector F (venting exhaust pipe and fixing straps are not supplied). 2 Installation The minimum distance between the upper pan support surfaces on the cooking appliance and the lowest part of the cooker hood should be no less than 50 cm in the case of electrical cookers and 70 cm in the case of gas or mixed cookers. If the installation instructions for the gas cooking appliance specify a greater distance, then follow that instruction. 6 5019_718_02006_GB 26-09-2007 11:33 Pagina 7 Installation The hood comes with plugs suitable for most walls/ceilings. You should however consult a qualified technician to make sure the installation is suitable for your kind of wall/ceiling. The wall/roof should be sufficiently strong to support the weight of the hood. Before installation: • Check that the product purchased is the right size for the area where it is to be installed. • To make installation easier, temporarily remove the grease filters and other parts that can be removed whose dismantling and assembly are described here. These should be refitted when installation is complete. • From the inside of the hood, make 2 pencil marks for the holes ready for the final fitting of the hood. • Remove the hood from the lower bracket. • Insert 2 wall plugs. Centre line support bracket mounting height reference centre line support bracket FRONT VIEW hooks bottom fastener locations Ø 8 mm REAR VIEW bottom screw hole (inside the canopy) hooks 8 5019_718_02006_GB 26-09-2007 11:33 Pagina 9 Installation • The hood has two identical brackets for attaching the chimney. Attach the first bracket (G – the side with fixing holes facing upwards – see Fig. 6) to the wall next to the ceiling, using the support bracket as a template (the small slots cut in the bracket should coincide with the centre lines previously traced on the wall), mark 2 holes with a pencil, drill the holes and attach the bracket with 2 screws and plugs. Attach the second bracket (M – the side with holes for attaching facing upwards – see Fig. 6) above the lower bracket at a distance of 200mm, attach the bracket with 2 screws and plugs. 2 rubber strips should be attached to the sides of this second bracket (one strip on each side – cut the rubber strip provided into two identical halves). • Recirculation mode Only: fit the deflector to the chimney support bracket. 6 • Chimney size: the chimney is supplied in a standard size and can then be cut to measure as shown in Fig. 7. chimney support bracket centre line Deflector lower support bracket lower fitting device bracket chimney support bracket bottom fastener locations 9 5019_718_02006_GB 26-09-2007 11:33 Pagina 10 Installation • Hook the hood onto the lower bracket. [. . . ] Cleaning The hood should be cleaned regularly both inside and out (at least as often as you carry out maintenance on the grease filters). 13 Disconnect the appliance from the mains supply. Before touching the light bulbs make sure they have cooled down. Remove the protective cover using a small flat screwdriver or a similar tool. [. . . ]