User manual WHIRLPOOL KCGT 6010/I PROGRAM CHART

[. . . ] Note: always use gloves when installing or carrying out maintenance work. Electrical connection The mains voltage should correspond with the voltage shown on the specifications label found inside the hood. If there is no plug, connect the hood to a socket that complies with current legislation and is in an easily accessible location. If there is no plug (direct connection to the mains supply) or the plug is not in an easily accessible location, fit a legally complying bi-polar switch that ensures the complete disconnection of the mains in the event of a category III line surge, in compliance with the installation regulations. IMPORTANT: before reconnecting the hood circuit to the power supply, check that it is working properly, that the mains cable has been properly fitted and that it has NOT been crushed in its holder during installation. [. . . ] Instead, it should be handed over to the applicable collection point for the recycling of electrical and electronic equipment. Disposal must be carried out in accordance with local environmental regulations for waste disposal. For more detailed information on treatment, recovery and recycling of this product, contact your local authority, the household waste disposal service or the shop where you purchased the product. 5 5019_718_02010_GB 30-05-2007 9:55 Pagina 6 Instructions for installation and use Follow the instructions in this manual carefully. All responsibility is denied for problems, damage or fire to the appliance resulting in failure to comply with the instructions in this manual. Extraction Modes The hood is designed to be used in two modes: Venting exhaust fumes to the outside, or by passing the air through a charcoal filter brfore recirculating the air back into the kitchen. Venting mode The hood comes with an upper air outlet B for the discharge of fumes to the outside (venting pipe and fixing straps not supplied). 1 Recirculation Mode This mode is to be used when it is not possible to vent the air to the outside. Air is purified by passing through activated charcoal filters (not provided) and recirculated back out into the kitchen. The air is sent back into the atmosphere via a pipe that passes through the cupboard cabinetry and is connected to the connector ring. 2 Installation The minimum distance between the upper pan support surfaces on the cooking appliance and the lowest part of the cooker hood should be no less than 50 cm in the case of electrical cookers and 70 cm in the case of gas or mixed cookers. If the installation instructions for the gas cooking appliance specify a greater distance, then follow this instruction. 6 5019_718_02010_GB 30-05-2007 9:55 Pagina 7 Installation The hood comes with plugs suitable for most walls / ceilings. You should however consult a qualified technician to make sure the installation is suitable for your kind of wall/ceiling. At this stage connect up the electrics on the control panel and the lights. • Hook the filter support frame onto the hood (snap fitting onto the two side seals). • Refit the grease filter. 5. 1 5. 2 5. 3 5. 4 CLACK! 8 5019_718_02010_GB 30-05-2007 9:55 Pagina 9 Hood description Fig. Handle for unhooking the grease filter 4. Halogen bulbs Functioning Turn to maximum speed when there is a lot of steam in the kitchen. We would advise you to turn the suction on 5 minutes before starting to cook and leave it running after you have finished cooking for about another 15 minutes. 1. ON/OFF light button: press to turn the light on or off. Motor ON/OFF button: press to turn the hood on or off. Once the hood is on, it sucks at the speed (power) of the previously selected suction. Intense extraction ON/OFF speed button: lasts about 5 minutes, after which the hood returns to previously selected extraction speed . Timer ON/OFF button: pressing this button can limit the running duration of the extraction selected, as follows: Speed 1 for 20 minutes. [. . . ] 9 Disconnect the appliance from the mains supply. Before touching the light bulbs make sure they have cooled down. Remove the protective cover using a small flat screwdriver or a similar tool. Only use 20W max (G4) halogen bulbs, and do not touch them with your bare hands. [. . . ]