User manual WHIRLPOOL KDDS 6010 INSTALLATION

[. . . ] 5019_102_00273_INSTAL_GB 30-05-2007 13:25 Pagina 1 KDDS 6010 - KDDD 6010 Assembly instructions 5019_102_00273_INSTAL_GB 30-05-2007 13:25 Pagina 2 5019_102_00273_INSTAL_GB 30-05-2007 13:25 Pagina 3 Note to the installer Note to the customer Parts supplied - double & single models Tools needed Installation preparation - double & signle models Electrical information - double & single models Service specifications - double models The cavity - double models Plumbing options - double models Service specifications - single models The cavity - single models Plumbing options - single models Installation instructions Step 1: moving the product into the cavity Step 2: removing the tub Step 3: adjusting the feet (double models only) Step 4: securing the product Step 5: refitting the tub Step 6: connecting the drain hoses Step 7: connecting the inlet hose and power supply Step 8: measuring the toe kick Step 9: trimming the toe kick (double models only)) Step 10: fitting the toe kick to the product (double models only) Step 11: Final checklist (double and single models) Step 12: customer support 4 4 5 5 6 7 8 9 10 11 12 13 14 14 15 16 17 17 18 19 19 20 20 21 21 5019_102_00273_INSTAL_GB 30-05-2007 13:25 Pagina 4 Note to the installer 1. Read these instructions completely and carefully. Installation of this R requires basic mechanical and electrical skills. 3. Be sure to leave these Instructions with the Customer. [. . . ] ** Depth of product excludes Curvature (30mm), or Handle. LENGTH OF SERVICES (FROM PRODUCT EXIT POINT) Drain hose - 2250mm Inlet hose - 1750mm Power supply cord - 1965mm NOTE: Services approximately exit product 189mm from left; 550mm from front; 393mm from top. 11 5019_102_00273_INSTAL_GB 30-05-2007 13:25 Pagina 12 The cavity - single models 100mm 10mm benchtop moisture protection tape 90° Moisture Protection Tape 10mm 412mm 5 m 05m + 97mm + Ø50mm services hole immediately adjacent to corner, can be either side 580mm throughout cavity 600mm + + Minimum thickness of cavity sides is 16mm 67mm These marks indicate mounting tab screw locations (refer to step 1 page 7) NOTE: All depth measurements are taken from the front face of the adjacent cabinetry. NOTE: To align drawer front to adjacent cabinetry, the product to counter top clearance can be increased from 3mm. Adjacent cabinetry must not extend above cavity base. WARNING!Ensure the edges of the services hole are smooth or covered to prevent damage to the power cord or hoses. 12 5019_102_00273_INSTAL_GB 30-05-2007 13:25 Pagina 13 Plumbing options - single models OPTION 1 and Standpipe Ø38mm with Air Gap. R POWER OUTLET WASTE ( 750 mm - 882. 5mm ) WATER SUPPLY VALVE 200mm MINIMUM BENDS RADIUS FROM VALVE WASTE OPTION 2 with Waste Disposal. Standpipe Ø38mm with Air Gap. R POWER OUTLET WASTE PLEASE NOTE: It is NOT recommended to connect the to any part of the Waste Disposal System. R ( 750 mm - 882. 5mm ) WASTE DISPOSAL VALVE WATER SUPPLY WASTE 200mm MINIMUM BENDS RADIUS FROM VALVE OPTION 3 using Sink Trap with Drain Hose Joiner. R 150mm ( 750 mm - 882. 5mm ) DRAIN HOSE JOINER VALVE WASTE WATER SUPPLY 200mm MINIMUM BENDS RADIUS FROM VALVE NOTE: Options 1 and 2 are the preferred options. Drains will need to be separated to satisfy Kosher requirements. We suggest you confirm acceptability with your local Rabbi in respect to Kosher installations. 13 MIN POWER OUTLET 5019_102_00273_INSTAL_GB 30-05-2007 13:25 Pagina 14 Installation instructions PLEASE NOTE: Your model of may differ from the model shown in the installation diagrams. For SINGLE MODELS, depending on the height of the cavity, the tub will need to be supported, eg. on a chair. 8 7 15 5019_102_00273_INSTAL_GB 30-05-2007 13:25 Pagina 16 Step 3: adjusting the feet (double models only) 9 - DOUBLE MODELS ONLY Adjust the height of the product to suit the cabinetry, by turning the feet from inside the product using a wrench or M5 socket. TIP - Gently take the load off each foot using the slide and then turn by hand. NOTE: For integrated products, the upper panel may be aligned with the top of the adjacent cabinetry, provided a minimum 5mm clearance from the bench is maintained. The product must be levelled to within 2. 5mm from front to back, and side to side. The product should NOT support any part of the kitchen cabinetry. TIP - Place a spirit level on the drawer runners to level the product. 5mm 9 16 5019_102_00273_INSTAL_GB 30-05-2007 13:25 Pagina 17 Step 4: securing the product 10 SINGLE MODELS ONLY Check the position of the chassis is still where marked on the cavity, before securing the product. 11 There are four 16mm round holes, two on the left and two on the right hand side in the sound insulation. These provide access to the mounting tabs. To secure the product to the cabinetry use a 16mm Phillips screw in each mounting tab. Make sure the sound insulation is positioned correctly before continuing installation. 12 Screw the two top tabs to the underside of bench. Tabs can accommodate a maximum of 19mm vertical gap. 11 10 12 Step 5: refitting the tub Important! [. . . ] Turn Toe Kick over, bend and then cut from front. Sand or scrape bottom edge to remove rough patches. 21 To avoid a cutting hazard remove all sharp edges after trimming. Remove all sharp edges 22 Remove Toe Kick tabs by snapping them off. 22 Step 10: fitting the toe kick to the product (double models only) 23 Partly open bottom drawer. [. . . ]