User manual WHIRLPOOL KHDD 3040 PROGRAM CHART

[. . . ] - Do not place flammable material on or near the appliance: A fire may break out if the appliance is inadvertently switched on. - Overheated oils and fats catch fire easily. Never leave the appliance unattended when cooking with fat and oil. - Do not place metal objects, such as kitchen utensils (knives, forks, spoons, lids, etc. ), on the cooking zone as they can become very hot. [. . . ] • Make sure you place the pot or pan in the centre of the cooking zone outlined on the hob. Declaration of conformity This appliance is designed to come into contact with food and complies with Regulation ( ) no. 1935/2004, and has been designed, constructed and marketed in compliance with the safety requirements of "Low Voltage" Directive 2006/95/EC (replacing 73/23/EEC as amended) and protection requirements of "EMC" Directive 2004/108/EC. 7 Before use IMPORTANT: the cooking zones will not switch on if pots and pans are not of the correct dimensions. Only use pots bearing the symbol "INDUCTION SYSTEM" (See figure opposite). Before switching the hob on, position the pot on the desired cooking zone. Using existing pots and pans Use a magnet to check whether pots or pans are suitable for use on the induction hob: pots are unsuitable if they cannot be magnetically detected. - Ensure pots have a smooth bottom, otherwise they may scratch the hob's glass ceramic surface. - Never place hot pots or pans on the hob's control panel. This could result in damage. OK NO Recommended pan base diameters Ø XL 24 cm 14 cm Ø 24 cm Ø L 21 cm 14 cm Ø 21 cm S Ø 14, 5 cm 9 cm Ø 14, 5 cm Installation After unpacking the hob, check that there has been no damage during transport. If in doubt, contact the dealer or After-sales Service. PREPARING THE HOUSING UNIT WARNING - Install a separator panel under the hob. - The lower part of the product must not be accessible after installation. - If there is an oven beneath the hob, do not install the separator panel. • For the distance between the underside of the appliance and the separator panel below, observe the dimensions given in the diagram. • Do not obstruct the minimum required clearance between the hob and the top of the unit to ensure the correct operation of the product. • Cut the worktop to fit before installing the hob and carefully remove any shavings or sawdust. min 5 min 20 min 5 8 Electrical connection WARNING - Disconnect the appliance from the mains power supply. - Installation must be carried out by a qualified electrician who is fully aware of current safety and installation regulations. The manufacturer declines all liability for injury to persons or animals and for damage to property resulting from failure to observe the regulations provided in this chapter. The power supply cable must be long enough to allow the hob to be removed from the worktop. Make sure the voltage specified on the appliance rating plate is the same as that of the house electrical system. Connecting to the terminal board For electrical connection, use an H05RR-F cable as specified in the table below. Conductors 230 V ~ + 230-240 V ~ + 230 V 3 ~ + 400 V 3N ~ + 400 V 2N ~ + Amount x size 3 x 2, 5 mm2 3 x 4 mm2 (Australia only) 4 x 1, 5 mm2 5 x 1, 5 mm2 4 x 1, 5 mm2 400 V 3N ~ 230 V ~ 230-240 V ~ (Australia only) 230 V ~ (UK only) A B C 400 V 2N ~ 230 V 3 ~ (Belgium only) 400 V 2N ~ (NL only) Connect the yellow/green earth wire to the terminal with the symbol . This wire must be longer than the other wires. Remove the terminal block cover (A), undoing the screw and inserting the cover in the terminal block hinge (B). 70 mm of sheath from the power supply cable. [. . . ] The control panel is locked with the exception of the OFF function. To unlock the controls, repeat the activation procedure. The luminous dot goes off and the hob is active again. Turn the hob off and on again to check if the problem has been eliminated. [. . . ]