User manual WHIRLPOOL KHDS 1160/I INSTRUCTION FOR USE

[. . . ] GB KHDF 1160 KHDS 1160 Instructions for use Product description and symbols Using the burners Practical advice on using the hob Positioning the pan supports and wok support Hood and cabinetry clearances (mm) Injectors table Warnings and suggestions Safeguarding the environment Installation (Flush and Semi-Flush fitting) Gas connection Electrical connection Fixing the Hob to the supporting structure. Traditionally fitted model (Semi Flush fitting) Fixing the Hob to the worktop. Flush fitted model Adaption to a different type of gas supply Replacing the injectors Fitting the wok burner Regulating the minimum flow level of the gas taps General cleaning & maintenance Care and maintenance of the gas burners Troubleshooting guide After Sales Service 4 4 5 5 6 6 7 8 9 9 10 10 11 12 12 13 13 14 14 15 15 Product description and symbols 1. Removable pan supports Auxiliary burner Semi-fast burner Semi-fast burner Professional wok burner Auxiliary burner control knob Semi-fast burner control knob Semi-fast burner control knob Professional wok burner control knob Control Symbols Off Maximum flame Minimum flame Using the burners To turn on one of the burners: 1. [. . . ] Warning: if you use a stainless steel flexible pipe, it must be installed in such a way that it does not come into contact with moving cabinetry like drawers or kitchen cupboards and passes at a point free of obstacles where it can be examined in its entirety. • After connecting to the gas mains, use soap and water to check there are no leaks. FOR BELGIUM ONLY: It is necessary to replace the elbow connection (A) on the appliance, with the one supplied. Important: if a stainless steel hose is used, it must be installed so as not to touch any mobile part of the furniture. It must pass through an area where there are no obstructions and where it is possible to inspect it on all its length. After connection to the gas supply, check for leaks with soapy water. Attention: Should you experience difficulty in turning the burners knobs, please contact the After Sales Service for the replacement of the burner tap. 9 Electrical connection The electrical connections must comply with current legislation and be carried out by a qualified, competent person. • Information on the voltage and power absorbed are shown on the serial no. • When installing the appliance, we recommend that this hob is protected by a 3mm bi-polar switch. • If damaged, the power cable must be replaced with an identical type of powercable ( H05V2V2-FT90ºC, or H05RR-F type). We recommend that this operation be conducted by our After Sales Service. Please contact our Customer Care Centre on 00800-3810-4026. • The manufacturer declines all responsibility for damage to persons, pets or goods as a result of failure to comply with the regulations above. L Earth (yellow/green) N Fixing the Hob to the supporting structure. Traditionally fitted model (Semi Flush fitting) Important: The following procedure shall be carried out by competent technical personnel only. The hob can be installed on different types of materials, such as masonry, metal, bare wood and heat resistant laminate coated wood (90°C). Cut an opening in the worktop to the dimensions shown in the diagram. Fix the hob using the fixing brackets provided. The appliance is supplied with two types of brackets: - no. 8 standard length brackets (Service code 4812 404 49874) for installation on kitchen tops with thickness over 40 mm - no. 8 long brackets (Service code 4812 404 49875) for installation on kitchen tops with thickness below 40 mm. The brackets must be fixed using the appropriate screws both at the front (no. 4) using the seats at the bottom of the hob (fig. [. . . ] Clean it each time you use it with a product specifically designed for brass. Use hot water and a mild deteregent to clean the the wok burner external cap (item (C) on page 12). Never use harsh products, or scourers that will damage the special surface coverings. Correctly refit the burners and caps in their place. [. . . ]