User manual WHIRLPOOL KHIS 6040 INSTRUCTION FOR USE

[. . . ] Instructions for use Installation diagrams Important safety information Safeguarding the environment Declaration of conformity Before use Using existing pots and pans Recommended pan base diameters Installation Electrical connection Instructions for use Cleaning Troubleshooting guide After-Sales Service Power level table Functions table Cooking table 4 6 7 7 7 8 8 8 9 10 14 14 15 16 17 18 Installation diagrams 180 mm 310/190 mm 180 mm MODEL KHIS 6520 / 6540 Min. 6 cm 4 Installation diagrams 5 Important safety information YOUR SAFETY AND THE SAFETY OF OTHERS ARE VERY IMPORTANT This manual and the appliance itself provide important safety messages, to be read and observed at all times. This is the safety alert symbol, pertaining to safety, which alerts users to potential hazards to themselves and others. All safety messages will follow the safety alert symbol and either the terms: HAZARD Indicates a hazardous situation which, if not avoided, will cause serious injury. [. . . ] Connecting to the terminal board Use an H05RR-F cable as indicated in the table below for the electrical connection. Conductors 230 V ~ + 230-240 V ~ + 230 V 3 ~ + 400 V 3N ~ + 400 V 2N ~ + Amount x size 3 x 4 mm2 3 x 4 mm2 (Australia only) 4 x 1, 5 mm2 5 x 1, 5 mm2 4 x 1, 5 mm2 400 V 3N ~ 230 V ~ 230-240 V ~ (Australia only) 230 V ~ (UK only) A B C 400 V 2N ~ 230 V 3 ~ (Belgium only) 400 V 2N ~ (NL only) Connect the yellow/green earth wire to the terminal with the symbol . This wire must be longer than the other wires. Remove the terminal block cover (A), undoing the screw and inserting the cover in the terminal block hinge (B). Insert the power supply cable into the cable clamp and connect the wires to the terminal board as indicated in the diagram next to the terminal board itself. Secure the power cable with the cable clamp. Close the cover (C) and screw it on the terminal block with the removed screw - point (1). Each time the cooktop is connected to the mains it carries out an automatic check which lasts several seconds. If the hob already has a power cable, follow the instructions attached to the cable. Connect the appliance to the mains electricity supply using a multipole switch disconnector with minimum contact gap of 3 mm. 9 Instructions for use Control Panel Description The control panel is equipped with touch controls: to use them, just press the corresponding symbol (a light touch is sufficient). To select and activate the cooking zones Switching/ the hob ON/OFF To set the minute minder To activate the flexible zone function To enable the hold function To select one of the automatic functions Slide touchscreen To lock the control panel First use / after a power failure After connecting the hob to the electrical power supply, the control panel is locked (the indicator light above the key is ON). To unlock the control panel, press and hold the key for 3 seconds. The indicator light switches off and the hob can be used normally. Switching the hob ON/OFF To switch the hob on, press and hold down the key for about 2 seconds: the indicator light above the key turns on and hyphens appear inside the cooking zone circles. To switch off, press the same key until the hob switches off. All the cooking zones are deactivated. i The hob automatically switches off if no function is selected within 10 seconds of switching on. 10 Instructions for use Activating and adjusting cooking zones Indicates that one of the automatic functions is On Cooking zone timer Cooking zone selection and selected cooking zone/power level display Slide touchscreen (power adjustment) After switching the hob on, position a pot on the required cooking zone. Activate the cooking zone by pressing the relative round key: the round key displays number corresponds to the intermediate power level. that If you are using a pot that is not suitable, not correctly positioned or not of the correct dimensions for your induction hob, the message "no pot" will appear in the display (see figure on the left). If no pot is detected within 60 seconds, the hob switches off. To change the power level, move your finger horizontally on the slide touchscreen: the number inside the circle changes from a minimum of 1 to a maximum of 9 depending on the position of the finger on the touchscreen. The booster function can be activated by pressing "BOOST" on the slide touchscreen ("P" on the display). The "BOOST" power level can be used for up to 10 minutes, after which the appliance automatically switches to level 9. If more than one cooking zone is on, the slide touchscreen allows you to change the power of the selected zone, indicated by the presence of a luminous dot at the bottom right of the power indicator. Flexible Zone This function allows you to use two cooking zones as an extra-large single zone. [. . . ] The connection voltage is wrong. The internal temperature of electronic parts is too high. The sensor detects a discrepancy between the appliance voltage and that of the mains supply. Wait for the hob to cool down before using it again. F42 or F43 Disconnect the hob from the mains and check the electrical connection. F12, F21, F25, F36, F37, Call the After-Sales Service and specify the error code. F40, F47, F56, F58, F60, F61, F62, F63, F64 14 After-Sales Service Before contacting the After-Sales Service 1. See if you can eliminate the problem on your own by referring to the "Troubleshooting guide". [. . . ]