User manual WHIRLPOOL KRIB 3625 INSTRUCTION FOR USE

[. . . ] Scrapping/Disposal The appliance is manufactured using recyclable material. This appliance is marked according to the European Directive 2002/96/EC, Waste Electrical and Electronic Equipment (WEEE). By ensuring this product is disposed off correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The symbol on the product, or on the documents accompanying this appliance indicates that this product should not be disposed off as household waste. [. . . ] • Do not use or place electrical appliances inside the product if they are not of the type expressly authorised by the Manufacturer. • This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. • To avoid the risk of children becoming trapped and suffocating, do not allow them to play or hide inside the appliance. • Do not eat ice cubes or ice lollies immediately after taking them out of the freezer since they may cause cold burns. USE • Before any maintenance or cleaning, unplug the plug from the power socket or switch off the electrical power. • Appliances must be connected to a water supply that only delivers drinking water (with mains water pressure of between 1. 7 and 8. 1 bar). • Make sure the voltage specified on the rating plate corresponds to that of your home. • Do not use single/multi adapters or extension cords. • For the water connection, use the pipe supplied with the new appliance; do not reuse that of the previous appliance. • Power cable modification or replacement must only be carried out by qualified personnel. • It must be possible to disconnect the appliance from the power supply by unplugging it or by means of a mains double-pole switch installed upstream of the socket. 5 Installation requirements Location zone conditions The ice maker machines are designed to operate at room temperature between 5ºC (41ºF) and 43ºC (109. 40ºF). Housing dimensions To install the ice maker in the correct way, it will be necessary that the hole located for such effect in the piece of furniture has the dimensions established in the drawing (560x440x560 mm). The drainage must be in the position indicated in the drawing. In the left part of the housing and below the inferior level of the machine. In this way the flexible pipes have the enough path to allow the extraction of the machine. Air vents Water drain IMPORTANT It must be taken into account that an exit must be left for the air that the machines takes through the front louver. It can be a back hole (with an outdoor exit) or a louver on the machine. The water connection, drainage and electrical steps of the equipment are also necessary (see the figure). 6 Technical specifications - Sizes: External: 596x455x22 Cabinet hole size: 560x440x560 - Mounting on sliding rails. - Production: Rated production: 10 Kg/24h (Ambient temperature 20°C / Water temperature 15°C). - 12 cubes/cycle - ice cube weight 22 g - Ice tank: 8 Kg - Power supply: 220 V / 50 Hz. - Power: 250 W - Intensity: 1. 8 A - Male thread tap socket ¾" BSP - Consumption: 2. 4 l/h - Maximum instantaneous capacity: 1 l/min - Pressure: 1-5 bar - Refrigerant: R134A - Air condensation. Back output. - Power supply connection: - Water connection: - Cooling: Installation Anchoring of the machine Follow the following steps: 1. Screw the guides in the hole of the piece of furniture to have them horizontally and set back 5 mm as it is indicated on the figure. 7 2. Screw the fastening bridge of the machine in the position of the drawing. [. . . ] Ice cube size This option can be selected to increase or decrease the size of the ice cubes based on personal needs. To increase or decrease size use the arrows. Language To change the language select Menu - Language and then the desired language. Press OK to confirm. 10 Startup The appliance is configured at the factory with preset values. [. . . ]