User manual WHIRLPOOL KRSM 9050 PRODUCT FICHE

[. . . ] The function disables automatically after 24 hours or can be switched off manually by pressing the button again. - Ice Mode (Type of ice) Press the "Ice mode" button to select the desired type of ice and to enable/disable the automatic ice maker. = ice cubes = crushed ice - no symbol displayed = automatic ice maker disabled Important: if the appliance is not connected to the water supply, the automatic ice maker must be disabled. 4 - Child Lock (Child Safety) To lock/unlock the buttons on the control panel and the water/ice dispenser, press the "Reset filter/alarm" and "Vacation mode" buttons at the same time until the symbol is displayed and the acoustic signal sounds. - Filter Alarm Reset (Acoustic alarm mute button) Press the "Reset Filter/Alarm" button to stop the acoustic alarm. [. . . ] When the function is enabled, the display only lights up when you use the appliance or the control panel, otherwise only the symbol is shown. Remember that this operation does not disconnect the appliance from the power supply. - Anti-bacterial filter Change the filter when the symbol blinks. After replacing the filter, press the "Reset filter/alarm" button until the symbol remains permanently on. - Vacation Mode (Vacation Function) This function can be used during extended absences. Press the "Vacation mode" button to enable/disable the function. When the function is enabled, the related symbol lights up and the refrigerator compartment becomes much less cold. After activating this function, remove all perishable foodstuffs from the compartment and leave the door closed: the refrigerator will maintain the right temperature to prevent odours from forming. The freezer compartment remains enabled: it is therefore possible to continue to use it as usual. - Water Water delivery is always available and the symbol is always displayed. - Water dispenser extraction The water dispenser features a swivel spout for easy filling of bottles, jugs and other large receptacles. If the doors do not open and close properly. The appliance may not be level. Clean the seals. If necessary, level the appliance (see Installation manual). The "Standby" function may have been enabled (depending on the model). The bulb may be burnt out. Disable the function (see the Quick Start Guide). Replace the bulb (see Instructions for Use, section "Maintenance and Cleaning"). The control panel will not do anything: The "Child Safety", "Key Lock" or every time a button "Ice/water dispenser lock" function may is pressed, the have been enabled. acoustic signal sounds. Disable the function (see the Quick Start Guide). The "Compartment door open" symbols Open door alarm. blinks and an The alarm is activated when the doors are acoustic signal left open for more than 2 minutes. sounds (if present) Close the doors or press the mute alarm button to switch off the acoustic signal. There are letters on the display, and an acoustic signal is sounding (if provided and not previously disabled). Malfunction Alarm The alarm indicates that a technical component has malfunctioned. Call an authorized After-Sales Service. Press the mute alarm button to switch off the acoustic signal. The "Eco mode" function may have been enabled. Disable the function (see the Quick Start Guide). 7 What to do if… Possible causes Solutions Blackout Alarm. This alarm activates when there has been an extended power failure causing the freezer compartment temperature to rise. The value flashing on The red Blackout Alarm LED and the the freezer display is the highest temperature reached during the power freezer temperature display failure. are blinking, and the acoustic signal is sounding (if provided). This alarm may be activated when the appliance is used for the first time. Press the mute alarm button to switch off the acoustic signal. [. . . ] The automatic icemaker does not work. Refer to the Quick Start Guide to enable the automatic ice maker again (on some models only). Water may not reach the automatic ice maker. Check that the product is connected to the mains water supply and that the water tap is open. The water filter may be clogged or installed incorrectly. Refer to the filter installation instructions to ensure that the filter was installed correctly and is not clogged. If installation or clogging is not a problem, call qualified personnel. 8 What to do if… Possible causes Solutions This is normal when the freezer door is open, or if the ice bucket is not installed correctly. Close the freezer door and/or check that the ice bucket is installed correctly. The "Child Safety" or "Ice/water dispenser lock" function may have been enabled. Disable the function (see the Quick Start Guide). The dispenser does not dispense ice when the lever is pressed. Ice cubes may be stuck because the ice dispenser has not been used for some time: The dispenser may not have been used for extended periods, causing the ice cubes to stick together. Change the ice selection from "ice cubes" to "crushed ice" or vice versa (in some models only), so as to remove any ice blocks. If the dispenser continues not to dispense ice, wait for two minutes and then repeat this operation. Shake the ice bucket to separate the cubes and increase the holding capacity. [. . . ]