User manual WHIRLPOOL KSCX 3625 INSTRUCTION FOR USE

[. . . ] Instructions for use Important safety instructions Preliminary steps Scrapping Declaration of conformity CE Built-in installation Product description Using the appliance for the first time Switching on and preheating Making coffee (using coffee beans) Changing the amount of coffee in the cup Adjusting the coffee grinder Making espresso with pre-ground coffee (instead of beans) Running off hot water Changing the amount of hot water Making cappuccino Changing the amount of milk and coffee for cappuccino Changing and setting menu parametrs Cleaning and maintenance Switching off the appliance Displayed messages Troubleshooting Technical data 4 5 5 5 6 8 9 9 10 11 11 11 12 12 12 13 13 16 18 19 20 21 Important safety instructions Your safety and that of others is paramount Failure to fully comply with the indications given in this user handbook can lead to electric shocks, serious injury, burns, fire, or damage to the appliance. Important warnings are accompanied by the following symbols. This is the danger symbol, pertaining to safety, which alerts users to potential risks to themselves and others. All safety warnings are preceded by the danger symbol and the following terms: DANGER: WARNING: Critical safety warnings Indicates a hazardous situation which, if not avoided, will result in serious injury. [. . . ] To do so, press the MENU button (B2) to access the menu; the display shows the message RINSING. The display shows 'OK' TO CONFIRM. Let the water run into the drip tray below or use it to fill (and then empty) the cup to be used for coffee, thus warming it. Changing the duration of operation The appliance is factory-set to switch off automatically after 30 minutes of inactivity. To change this time (max 120 min. ), proceed as follows: • Press the MENU button (B2) to access the menu and then buttons (B5) and (B6) until the display shows the message AUTO-OFF. • Press buttons (B5) and (B6) to set the period of time after which the appliance must switch off (30 minutes, 1 hour, 2 hours). • Press the MENU button (B2) to exit the menu. Setting the clock • Press the MENU button (B2) to access the menu and then buttons (B5) and (B6) until the display shows the message ADJUST TIME. • To set the hours, use buttons (B5) and (B6) then press • To set the minutes, use buttons (B5) and (B6) and then press (B7) to confirm. • Press the MENU button (B2) to exit the menu. Setting automatic start time This function allows you to set the machine to switch on automatically at a time of your choosing. • Make sure the appliance clock has been set. • Press the MENU button (B2) to access the menu and then buttons (B5) and (B6) until the display shows the message AUTO-START. • The machine displays the message AUTO-START ENABLE?• The display shows AUTO-START 07:30. • To set the auto start time, use the buttons (B5) and (B6) then press (B7) to confirm. • To set the minutes, use buttons (B5) and (B6) and then press (B7) to confirm. • Press (B7), the display shows AUTO-START ENABLED. Changing the coffee temperature To change the temperature of coffee run off, proceed as follows: • Press the MENU button (B2) to access the menu and then buttons (B5) and (B6) until the display shows the message COFFEE TEMPERATURE; • Press (B7). • Press buttons (B5) and (B6) to select the required coffee temperature: low, medium, high. • Press (B7) to confirm the temperature chosen. • Press the MENU button (B2) to exit the menu. [. . . ] - Turn the grinding adjustment knob one click clockwise towards the number 7 while the coffee mill is in operation (Figure 14). Continue one click at a time until coffee run-off is satisfactory. Results are only visible after running off 2 coffees. The coffee is not creamy enough. - The blend of coffee is unsuitable. The coffee runs out too slowly - The coffee is ground too finely. or in drips. The coffee runs out too quickly. - The coffee is ground too coarsely. - Turn the grinding adjustment knob one click anticlockwise towards the number 1 while the coffee mill is in operation (Figure 14). [. . . ]