User manual WHIRLPOOL LOP 1070 IG PRODUCT FICHE

[. . . ] • Install the appliance on a solid and level floor surface, preferably in a corner of the room. • Make sure that all four feet are stable and resting on the floor and then check that the appliance is perfectly level using a spirit level (see Installation/ Adjust the feet”). 4. Water supply • Connect the water supply inlet hose in accordance with the regulations of your local water company (see “Installation/Connect the water inlet hose”). • Water supply: Cold water only • Tap: 3/4” threaded hose connector. • Pressure: 0. 05-1. 00 MPa (0. 5-10 bar). 14 Black process 45. 0° 150. 0 LPI 50120020GB. fm Page 15 Tuesday, November 23, 2004 6:23 PM PRECAUTIONS AND GENERAL RECOMMENDATIONS 1. Packing • The packing material is recyclable as indicated by the recycling symbol . [. . . ] After-Sales Service sticker (inside door) 8. Technical specifications sticker (inside cover) 1 3 2 4 7 5 8 6 9 Minimum housing dimensions Width Height Depth (depending on the appliance) 595 mm 850 mm 395 or 335 mm / 530 or 580 mm FILLING THE DETERGENT AND ADDITIVES 1. Pull out the detergent dispenser completely, until the limit. Add the detergent: • Programme with pre- and main wash • Main wash programme without prewash • Fabric softeners, conditioners and chlorine bleach: no more than to “MAX” mark • Stain remover • Water softener (water hardness class 4) • Starch (dissolved in water) 3. Close the detergent dispenser completely. Water hardness: soft water requires less detergent. WATER HARDNESS CATEGORY: CHARACTERISTICS GERMAN °dh FRENCH °fh ENGLISH °eh 1 2 3 4 16 soft average hard very hard 0-7 7-14 14-21 over 21 0-12 12-25 25-37 over 37 0-9 9-17 17-26 over 26 Black process 45. 0° 150. 0 LPI 50120020GB. fm Page 17 Tuesday, November 23, 2004 6:23 PM REMOVING THE FILTER 1. Slowly turn the filter anticlockwise without extracting it as yet. Now unscrew the filter completely and extract it. Remove any foreign items from the foreign body trap. Insert the filter and screw it in clockwise until it locks, making sure it is hermetically closed. Pour 0. 5 l of water into the detergent dispenser to reactivate the “Eco System”. Connect the appliance to the electrical outlet. 18 Black process 45. 0° 150. 0 LPI 50120020GB. fm Page 19 Tuesday, November 23, 2004 6:23 PM INSTALLATION Remove the transport bolts For washing machines: 1. Slacken the three or four bolts (A) (according to model) with the spanner supplied. Slacken and remove the screws “A” which lock the drum during transport by following the instructions given at the side. Unscrew the bolts by hand. A B A B A B A A A B A A 1 1 For washing machines: 3. Hold the screws together with the plastic spacers and remove them. Keep the transport bolts for future use. Close the holes with the plastic covers (supplied with the documents). Insert a screwdriver into the empty holes and tilt to remove the plastic spacers (C) (transport bolts) and retrieve them. Keep the transport bolts for future use. For both washing machines and washer dryers: Note: If the plastic spacers remain inside the appliance: Open the rear panel by removing the twelve screws, remove the spacers and replace the panel. 4 3 Refit the transport bolts Fit the transport bolts before transporting the appliance as follows: For washing machines: 1. Pry off the plastic covers with a screwdriver and remove them. [. . . ] Carefully screw the hose connection to the appliance inlet, preferably by hand. Turn the tap on fully and check that the joints at the appliance and the tap are watertight. If the hose is too short, replace it with a suitable length of pressure resistant hose (1000 kPa min, EN 50084 approved type). Check the hose regularly for brittleness and cracks and replace if necessary. [. . . ]