User manual WHIRLPOOL LTE 1178 EG INSTRUCTION FOR USE

[. . . ] IFU-TL HR GB. fm Page 1 Friday, November 7, 2008 2:30 PM CONTENTS DEFINITION OF USE BEFORE USING THE WASHING MACHINE PRECAUTIONS AND GENERAL RECOMMENDATIONS DESCRIPTION OF THE WASHING MACHINE BEFORE THE FIRST WASH CYCLE PREPARATION OF THE WASHING DETERGENTS AND ADDITIVES CLEANING THE FILTER/ DRAINING RESIDUAL WATER CARE AND MAINTENANCE TROUBLESHOOTING GUIDE AFTER-SALES SERVICE TRANSPORT AND HANDLING INSTALLATION ELECTRICAL CONNECTION Black process 45. 0° 100. 0 LPI IFU-TL HR GB. fm Page 2 Friday, November 7, 2008 2:30 PM DEFINITION OF USE This washing machine is exclusively destined to wash machine washable laundry in quantities which are usual for private households. • Observe the instructions given in these Instructions for Use and the Programme Chart when using the washing machine. • Keep these Instructions for Use and the Programme Chart; if you pass on the washing machine to another person, also give him/her Instructions for Use and Programme Chart. BEFORE USING THE WASHING MACHINE 1. Remove the top protection and the protective corners. [. . . ] Pull the dispenser towards you and remove it. A small quantity of water can remain in the dispenser. It is advisable to carry the dispenser in an upright position. You can also remove the siphon caps in the dispenser for cleaning. Replace the siphon caps in the dispenser (if removed). Replace the dispenser by locating the bottom tabs in the lid holes and pivot until both of the upper buttons lock. Note: ensure that the detergent dispenser is correctly reinstalled. Water inlet hose filter Check and clean regularly (at least two or three times a year). Carefully clean the filter located at the end of hose, without disassembling it, for example with a tooth-brush. Note: Do not submerge the hose in water. Screw the flexible hose back onto the tap by hand. Do not use pliers (risk of squashing the joint). Turn on the tap and check that the connections are water-tight. Plug the washing machine back in. Safety valve inspection window A B Water inlet hose Check the inlet hose regularly for brittleness and cracks and replace it if necessary using a new hose of the same type. The inlet hose as shown on picture “A” has a safety valve to prevent the appliance against uncontrolled water inlet; if the safety valve inspection window is red, the safety valve has been activated and the hose must be exchanged. Contact out AfterSales Service or your specialist dealer to obtain a new inlet hose. If your inlet hose has a transparent hose coating (fig. “B”), periodically check the colour of the transparent coating. If the transparent hose coating turns into an intense red, this is an indication that the hose may have a leak and should be replaced. Contact our After-Sales Service team or specialist dealer to obtain a replacement hose. C GB 10 Black process 45. 0° 100. 0 LPI IFU-TL HR GB. fm Page 11 Friday, November 7, 2008 2:30 PM Appliance exterior and control panel • Clean with a soft damp cloth. • If necessary, a neutral household cleaner can be applied (do not use aggressive or abrasive products). Lid seal • Check the condition of the lid seal periodically and clean it from time to time with a damp cloth. Water inlet hose(s) • Check the hose regularly for brittleness and cracks. Replace if necessary. Appliance interior • After each washing, leave the lid open for some time to allow the inside of the appliance to dry. • If you never or seldom wash your laundry at 95°C, we recommend to occasionally run a 95°C programme without laundry, adding a small amount of detergent, to keep the interior of the appliance clean. Filter • Check and clean the filter regularly, at least 3 or 4 times a year (see “Cleaning the Filter/ Draining Residual Water”). Do not use flammable fluids for cleaning the appliance. [. . . ] Unhook the drain hose from the left clip, see arrow “A” on picture. Important: Do NOT loosen the drain hose from the right connection, see arrow “B” on picture. Otherwise, there is the risk of leakage and of scalding with hot water. Fix the “U” bend (“C”) at the very end of the drain hose. [. . . ]