User manual WHIRLPOOL MFW108EDWT MM PRODUCT FICHE

[. . . ] This programme (40°C) is tested and approved by The Woolmark Company for handwashable wool. This programme is particularly suitable to treat delicate lingerie (use of a laundry net strongly recommended). Normally soiled cotton jeanswear and garments made of robust jeanslike material such as trousers and jackets. Normally soiled and sweaty sportswear made of cotton jersey or microfibres. [. . . ] M0702 5019 901 01763 Black process 45. 0° 150. 0 LPI 90101763GB. fm Page 2 Tuesday, April 27, 2010 2:45 PM CONSUMPTION DATA Programme Cotton (Hygienic) Coloured*** Coloured Synthetics Synthetics Delicate Woolens Hand Lingerie Jeans Sport Super Eco Everyday Wash Express Wash 15’ Temperature (°C) 95 60 40 60 40 30 40 40 30 40 30 60 40 30 Load (kg) max. 6. 0 3. 0 Water (l) 82** 59 77 46** 42 60 60 45 45 95 54 75 73 30 Energy (kWh) 2. 40 1. 36 0. 75 0. 85 0. 50 0. 40 0. 60 0. 60 0. 35 0. 80 0. 55 0. 95 0. 60 0. 20 Approx. Programme Duration (hours : minutes)* 2:10 2:20 2:05 1:35 1:20 0:45 0:45 0:40 0:36 2:21 1:34 4:00 1:00 0:15 START DELAY The “Start delay” allows to run the machine at the consumer’s convenience, for example at night when electricity is cheaper. Do not use liquid detergent when activating the “Start delay”. • Select programme, temperature and options. • Press the “Start delay” button to select a delay time up to 23 hours; the light of the “Start (Pause)” button blinks. • Press the “Start (Pause)” button; the countdown of the delay time begins. The light of the “Start (Pause)” button stops blinking and is on; the light of the start delay button will keep blinking until the programme starts. • As soon as the programme starts, the start delay on the display is replaced by the remaining programme time, and the light of the “Start delay” button goes off. • Once having pressed the “Start (Pause)” button, the number of hours preselected can be changed by pressing and holding the “Start delay” button. To cancel the “Start delay” . . . before you press “Start (Pause)”: • Turn the programme selector to another position or press the “Reset/Drain” button. • The washing machine stops to rinse hold as soon as the “Rinse hold” light in the programme sequence indicator blinks; the “Start (Pause)” button also blinks. To terminate the “Rinse hold” : • If you want to drain only without spinning: Press the “Start (Pause)” button to start the drain process. • If you want to spin your laundry: Press the “Variable spin” button to select the desired spin speed and then “Start (Pause)” to start the spin cycle. “Variable spin” button • Every programme has a predefined spin speed. • Press the button to set another spin speed. • If you select spin speed “0”, the final spinning is cancelled but intermediate spin peaks remain during rinse. The water is drained out only. PROGRAMME END • 1. • The display shows “End” and the “Door open” indication lights. Turn the programme selector to the “Off/O” position. Leave the door ajar to allow the drum to dry. PROGRAMME START Open the tap and press “Start (Pause)”; the light stops blinking and is on. The programme sequence indicator shows the current programme phase, running from left to right through Wash, Rinse, Spin/Drain. [. . . ] The child lock cannot be activated or deactivated when the programme selector is in the “Off/O” position. To activate the child lock: • Turn the programme selector to a programme position, or run a programme as usual. • Press the 2 buttons marked with the key symbol simultaneously for at least 3 seconds; a key-like symbol will shortly appear on the display to indicate that the child lock is active. Any time you try to change a programme setting with active child lock, the display will shortly show the key-like symbol. [. . . ]