User manual WHIRLPOOL PIT 400/NE PROGRAM CHART

[. . . ] 61902018GB. fm Page 3 Thursday, January 8, 2009 11:15 AM 180 mm 210 mm 145 mm 145 mm 240 mm 145 mm 180 mm ENGLISH FRANÇAIS Instructions for use Mode d’emploi Page 4 Page 11 3 61902018GB. fm Page 4 Thursday, January 8, 2009 11:15 AM IMPORTANT SAFETY INFORMATION This manual contains important information regarding safety, the use and maintenance of your new hob. Read the manual carefully and keep it in an easily accessible place for future consultation. section “Troubleshooting Guide”). When the temperature returns to within normal levels the hob is able to be switched on again. [. . . ] If necessary, cut the kitchen unit and worktop to fit before installing the hob. Clean the cutout of any chips that could compromise appliance operation. 770 510 +1 0 510 +1 0 483 553 min. 8 +2 0 490 560 490 +2 0 750 For flush mounted installation or setting into a marble worktop, contact the After-sales Service for the installation kit and necessary instructions. • 4812 310 19277 Installation kit for marble worktop. • 4801 211 00112 Installation kit for flush fitted worktop. To guarantee correct operation, the appliance must be installed on a perfectly flat surface. If necessary, cut the kitchen unit and worktop to fit before installing the hob. Clean the cutout of any remaining dust that could compromise appliance operation. For the distance between the underside of the induction hob and the kitchen unit (or separating panel), observe the dimensions given in the figure at the side. If a column unit is installed adjacent to the hob, leave a distance of at least 100 mm from the edge of the hob. min. Position the clips (A) in the spaces provided on the hob trim (fig. Measure the centre point of the vertical sides of the cut-out (fig. Fit the brackets (C) in the centre of the vertical sides, aligning the upper edge of the brackets so that they are flush with the worktop surface (fig. Fix the brackets with the 4 screws supplied (B) using the holes provided. Insert the hob in the cutout, making sure the clips (A) are secured in the spaces provided (fig. 2 6 61902018GB. fm Page 7 Thursday, January 8, 2009 11:15 AM A fig. 4 Undercounter oven installation: • If an oven (which must be of our manufacture) is to be installed under the hob, ensure it is equipped with a cooling system and observe the distances given in the figure to the side. • There must be nothing between the cooktop and the oven (cross rails, panels, brackets, etc. ). 5 mm OPERATING INSTRUCTIONS Control panel Timer On/Off Child lock the symbols are not active!To select the desired functions, touch the areas below. Cooking zone controls and corresponding display Control panel graphics shown in these instructions might not match exactly the graphics of your hob. Button's functions are the same for all hob models. If the hob has been in use, the residual heat indicator “H” remains lit until the cooking zones have cooled down. The hob automatically switches off if no function is selected within 10 seconds of switching on. Switching the hob ON/OFF To switch the hob on, press the button for approx. 2 seconds until the cooking zone displays light up. To switch off, press the same button until the displays switch off. [. . . ] Glass scrapers have a very sharp blade and must be handled with care. Remove any stubborn food residues with a scraper or proprietary detergents. Salt, sugar and sand can scratch the glass ceramic hob: clean up any such spills on the hob immediately. Troubleshooting Guide • Before contacting After-sales Service: • read and follow the instructions given in the section “Operating instructions”. • Connect the hob to the electricity supply and check that the supply has not been shut off. ERROR CODE The hob switches off and after 30 seconds emits an acoustic signal every 4 seconds C81, C82 DESCRIPTION Continuous pressure on control panel area The control panel switches off because of excessively high temperatures The connection voltage is wrong • Clean the hob and dry it thoroughly. [. . . ]