User manual WHIRLPOOL RY160LXTS INSTALLATION

[. . . ] INSTALLATION INSTRUCTIONS SLIDE-IN ELECTRIC RANGE Table of Contents RANGE SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 INSTALLATION REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Tools and Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Location Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Electrical Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Countertop Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 INSTALLATION INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Unpack Range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Adjust Leveling Legs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Install Anti-Tip Bracket. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Electrical Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Verify Anti-Tip Bracket Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Level Range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Complete Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Moving the Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 RANGE SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING. " These words mean: DANGER WARNING You can be killed or seriously injured if you don't immediately follow instructions. [. . . ] NOTE: If height adjustment is made when range is standing, tilt the range back to adjust the front legs, then tilt forward to adjust the rear legs. When the range is at the correct height, check that there is adequate clearance under the range for the anti-tip bracket. Before sliding range into its final position, check that the antitip bracket will slide under the range and onto the rear leveling leg prior to anti-tip bracket installation. Anti-tip bracket Install Anti-Tip Bracket 1. Remove the anti-tip bracket that is taped in the storage drawer. Determine which mounting method to use: floor or wall. If you have a stone or masonry floor you can use the wall mounting method. 5. Using the Phillips screwdriver, mount anti-tip bracket to the wall or floor with the two #12 x 1/" screws provided. 5 Electrical Connection Power Supply Cord Direct Wire WARNING WARNING Electrical Shock Hazard Disconnect power before servicing. Failure to follow these instructions can result in death, fire, or electrical shock. Electrical Shock Hazard Disconnect power before servicing. Use 8 gauge copper or 6 gauge aluminum wire. Failure to follow these instructions can result in death, fire, or electrical shock. 1. Use Phillips screwdriver to remove the terminal block cover screw located on the back of the range. Pull cover down and toward you to remove cover. Feed the power supply cord through the opening in the cord/conduit plate on bottom of range. Allow enough slack to easily attach the wiring to the terminal block. Tighten strain relief screw against the power supply cord. Style 2: Direct wire strain relief 3. Remove plastic tag holding three 10-32 hex nuts from the middle post of the terminal block. Use Phillips screwdriver to remove screws from panel on back of range. USE TAG!CORD REMOVEPOWER WITH ETIQUETA LA EL TUERCAS NUTS QUITE LAS USE CONECTAR ELÉCTRICO PARA CORDÓN 4. Style 1: Power supply cord strain relief Assemble a UL listed strain relief in the opening. A A. UL listed strain relief 6 Lift range back panel up and off. Assemble a UL listed conduit connector in the opening. USE TAG!CORD REMOVEPOWER WITH ETIQUETA LA TUERCAS EL NUTS QUITE LAS USE CONECTAR ELÉCTRICO PARA CORDÓN A B Use Phillips screwdriver to remove screws and slide cord/conduit plate down and out. A. Strain relief Feed the flexible conduit through the strain relief, allowing enough slack to easily attach wiring to the terminal block. Tighten strain relief screw against the flexible conduit. Position cord/conduit plate as shown in the following illustration. 5. [. . . ] If there is an extra part, go back through the steps to see which step was skipped. Dispose of/recycle all packaging materials. Use a mild solution of liquid household cleaner and warm water to remove waxy residue caused by protective shipping material. For more information, read the "Range Care" section of the Use and Care Guide. [. . . ]