User manual WHIRLPOOL SC8720EDB INSTALLATION

[. . . ] Installation Instructions Quick Reference Table of Contents: Pages 1 Before you start 1 Cutout dimensions 1 Clearance dimensions 2 Product dimensions 2 Tools and materials needed 2 Parts supplied 2 Electrical requirements 3 Gas supply requirements 3 5 4 Venting requirements 6 Installation steps 7 Gas conversions Back cover Cooktop removal Need assistance? Check your Use and Care Guide for a toll-free number to call, or call the dealer from whom you purchased the cooktop when you: Have questions about the cooktop installation or operation. Need to obtain the name and number of an authorized service company. The dealer is listed in the Yellow Pages of your phone directory under "Appliances -- Household -- Major -- Service and Repair. " When you call, you will need: The cooktop model number. Both numbers are listed on the model/serial rating plate, located on the bottom of the right side of the downdraft plenum. [. . . ] (61 cm) 5" to 6" transition 4 ft. (122 cm) 6", 90° elbows 6", wall cap 6 ft. of Pieces/ Length Total Equivalent Length 1 ft. (61 cm) 6" round 90° elbow 5 ft. (152 cm) 90° elbows (2) 12 feet (366 cm) straight 5" to 6" transition Wall cap = 10 ft. = 0 ft. (305 cm) (366cm) (30. 5 cm) (0cm) (701. 5 cm) Equivalent length of 6" round system = 23 ft. 3-1/4" x 10" flat elbow 12 ft. (366 cm) (In this example, blower can be left in "Low" range as set at factory. ) 3-1/4" x 10" 90° elbow 5 ft. (152 cm) transition to round 5" to 6" air flow 3-1/4" x 10" to 6" 90° elbow air flow 3-1/4" x 10" to 6" Vent system equivalent length greater than 30 feet -- blower should be set at "High" range. Example: blower 1 ft. (61 cm) 5" to 6" transition transition to flat 5" to 3-1/4" x 10" 90° elbow air flow this direction not recommended air flow 6" to 3-1/4" x 10" 90° elbow air flow 6" to 3-1/4" x 10" air flow wall cap* 3-1/4" x 10" 4 ft. (183 cm) 6", 90° elbows Shifting blower to "High" range To shift blower to "High" range: 1. Remove the air grille and filter from blower housing. Snap the spring-loaded restricter ring out of the blower inlet. Reinstall the filter and air grille. 6 ft. (30. 5 cm) 6" to 3-1/4" x 10" transition 0 ft. (0 cm) 3-1/4" x 10" wall cap 10 ft. (305 cm) 5" or 6" round 0 ft. (0 cm) roof cap* 10" x 10" 0 ft. (0 cm) 90° elbows (3) 5" to 6" transition 6" to 3-1/4" x 10" transition Wall cap 16 feet (488 cm) 6" straight 10 feet (305 cm) 3-1/4" x 10" straight = 15 ft. ( 457. 2 cm) 30. 5 cm) 30. 5 cm) 0 cm) 488 cm) 305 cm) thermal break 5" or 6" round 2 ft. (61 cm) Equivalent length of 6" round system = 43 ft. (1311. 2 cm) (In this example, blower MUST be shifted to "High" range. ) Note: Flexible metal vent is Not recommended. If it is used, calculate each foot of flexible duct as two feet of straight metal vent. [. . . ] 0. 037"): Install on RIGHT rear and front burners. Place Natural gas hoods in plastic parts bag for future use. Reattach bag to plenum. Remove surface burner and grille modules from cooktop. gas orifice hoods by turning hoods counterclockwise with 1/2" open-end wrench. [. . . ]