User manual WHIRLPOOL TGV 6730/IN INSTRUCTION FOR USE

[. . . ] Indicates a hazardous situation which, if not avoided, could cause serious injury. SAVE THESE INSTRUCTIONS INSTALLATION After unpacking the hob, make sure that it has not been damaged during transport. In the event of problems, contact the dealer or your nearest After-sales Service. All Safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed. - The appliance must be disconnected from the power supply before carrying out any installation work. - Installation and maintenance must be carried out by a qualified technician, in compliance with the manufacturer’s instructions and local safety regulations. [. . . ] It must pass through an area where there are no obstructions and where it is possible to inspect it on all its length. • After connection to the gas supply, check for leaks with soapy water. Light up the burners and turn the knobs from max position to minimum position to check flame stability. 5019 419 01197 Manufacturer: Whirlpool Europe S. r. l. Borghi, 27 21025 Comerio (VA) ITALY ELECTRICAL CONNECTION WARNING WARNING This operation must be performed by a qualified technician. • • • The electrical connections must comply with local regulations. The earthing of this appliance is compulsory by law. L Earth (yellow/green) N REPLACING THE INJECTORS (see the injector table in the Instruction) 1. Using a suitable wrench (C), unscrew the injector to be replaced. Replace it with the injector required for the new type of gas. Before installing the hob, remember to apply the gas setting label supplied with the injectors, so that it covers the information already present. N. B. : do not place the small grates with closed arms on the WOK burner. IMPORTANT: the data relevant to the voltage and power absorption are indicated on the rating plate. ASSEMBLY After having cleaned the perimeter surface, apply the supplied gasket to the hob as shown in the figure. Position the hob in the worktop opening made respecting the dimensions indicated in the Instruction. NOTE: the power supply cable must be long enough to permit its upward extraction. To secure the hob, use the brackets (A) provided with it. Fit the brackets into the relevant bores shown by the arrow and fasten them by means of their screws in accordance with the thickness of the worktop. ADJUSTING MINIMUM GAS SETTING OF TAPS To ensure correct adjustment of the minimum setting, remove knob (E) and proceed as follows: • tighten (-) to decrease the height of the flame; • loosen (+) to increase the height of the flame. Adjustment must be carried out with the tap in minimum position (small flame) . After adjusting, reinstate the seals with sealing wax or equivalent material. The primary air of the burners does not need adjusting. After adjusting, light the burners and turn the knobs from max. to check flame A 4x 4x 4x REFERENCE TO LOCAL REGULATIONS Installation must be performed in accordance with standard NBN D 51-003. AFTER-SALES SERVICE NO ADJUSTMENT TO DIFFERENT TYPES OF GAS WARNING This operation must be performed by a qualified technician. Before calling the After-Sales Service, make sure you can give the following information: - type of fault or problem; - exact model (written on the label affixed to the instruction/warranty); - service number that follows the word SERVICE on the rating plate under the hob and on the label affixed to instruction/warranty; - your complete address and phone number. If any repairs are required, please contact an authorised After-Sales Service, as indicated in the warranty. If the appliance is intended to operate with a different gas from the gas type stated on the rating plate and information label on the top of the hob, change the injectors. Remove the information label and keep it with the instructions booklet. Use pressure regulators suitable for the gas pressure indicated in the Instruction. [. . . ] This burner safety device shuts off the gas supply to the burner if the flame goes out accidentally (because of sudden draught, an interruption in the gas delivery, boiling over of liquids, etc. ). • The knob must not be pressed for more than 15 sec. If, after that time has elapsed, the burner does not remain lit, wait at least one minute before trying to light it again. NOTE: should particular local conditions of the delivered gas make the ignition of burner difficult, it is advisable to repeat the operation with the knob turned to small flame setting. [. . . ]