User manual WHIRLPOOL TGV 6731/IN INSTRUCTION FOR USE

[. . . ] GB TGV 6731 BUILT-IN GAS HOB - BE The use of a gas appliance produces heat and humidity in the room. Make sure the room is well-ventilated, or install an extractor hood with exhaust duct. In case of prolonged use, additional ventilation may be necessary (by opening a window or increasing the hood extraction speed). After use, make sure the knobs are in off position and close the main gas supply cock or the gas cylinder valve. [. . . ] IMPORTANT: if a stainless steel hose is used, it must be installed so as not to touch any mobile part of the furniture. It must pass through an area where there are no obstructions and where it is possible to inspect it on all its length. • After connection to the gas supply, check for leaks with soapy water. Light up the burners and turn the knobs from max position to minimum position to check flame stability. 5019 419 01198 Manufacturer: Whirlpool Europe S. r. l. Borghi, 27 21025 Comerio (VA) ITALY ELECTRICAL CONNECTION WARNING WARNING This operation must be performed by a qualified technician. • • • The electrical connections must comply with local regulations. The earthing of this appliance is compulsory by law. L Earth (yellow/green) N REPLACING THE INJECTORS (see the injector table in the Instruction) 1. Using a suitable wrench (C), unscrew the injector to be replaced. Replace it with the injector required for the new type of gas. Before installing the hob, remember to apply the gas setting label supplied with the injectors, so that it covers the information already present. N. B. : do not place the small grates with closed arms on the WOK burner. IMPORTANT: the data relevant to the voltage and power absorption are indicated on the rating plate. ASSEMBLY After having cleaned the perimeter surface, apply the supplied gasket to the hob as shown in the figure. Position the hob in the worktop opening made respecting the dimensions indicated in the Instruction. NOTE: the power supply cable must be long enough to permit its upward extraction. To secure the hob, use the brackets (A) provided with it. Fit the brackets into the relevant bores shown by the arrow and fasten them by means of their screws in accordance with the thickness of the worktop. ADJUSTING MINIMUM GAS SETTING OF TAPS To ensure correct adjustment of the minimum setting, remove knob (E) and proceed as follows: • tighten (-) to decrease the height of the flame; • loosen (+) to increase the height of the flame. Adjustment must be carried out with the tap in minimum position (small flame) . After adjusting, reinstate the seals with sealing wax or equivalent material. The primary air of the burners does not need adjusting. After adjusting, light the burners and turn the knobs from max. to check flame A 4x 4x 4x REFERENCE TO LOCAL REGULATIONS NO The appliance is supplied with a 1/2” threaded conical end to be connected to the gas supply (according to ISO regulations ISO 7/1 RP 1/2). The connection must be effected in accordance with standard NBN D 51-003 using rigid piping or in accordance with specifications sheet A. R. G. B. /03 using flexible tubing. The appliance must be installed complete with an AGB-approved stop valve. AFTER-SALES SERVICE Before calling the After-Sales Service, make sure you can give the following information: - type of fault or problem; - exact model (written on the label affixed to the instruction/warranty); - service number that follows the word SERVICE on the rating plate under the hob and on the label affixed to instruction/warranty; - your complete address and phone number. [. . . ] Any baked-on food should be removed with a toothpick or needle. NOTE: to avoid damaging the electric ignition device, do not use it when the burners are not in their housing. 1. Semi-rapid burner control knob CLEANING THE HOB PARTS 3 5 6 7 Symbols Solid disc Large flame Small flame Tap closed Max. opening or reduced delivery PRATICAL ADVICE FOR USING THE BURNERS This hob has burners of different diameters. [. . . ]