User manual WHIRLPOOL TGW 5466/IN/01 INSTRUCTION FOR USE

[. . . ] Do not repair or replace any part of the appliance unless specifically stated in the user manual. TECHNICAL INFORMATION FOR THE INSTALLER • • This product can be embedded in a worktop 20 to 60 mm thick. If there is no oven beneath the hob, insert a separator panel that has a surface at least equal to the opening in the work surface. This panel must be positioned at a maximum distance of 150 mm below the upper surface of the work surface but, in no case less than 20 mm from the bottom of the hob. In the case that you intend to install an oven beneath the hob, make sure that it is manufactured by Whirlpool and equipped with a cooling system. [. . . ] - This hob (class 3) is designed solely for private household use for cooking food. Do not use this appliance as a space heater to heat or warm the room. Doing so may result in carbon monoxide poisoning and overheating of the hob. The Manufacturer declines all responsibility for inappropriate use or incorrect setting of the controls. - The appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or with lack of experience and knowledge of the appliance, unless supervised or previously instructed in its use by those responsible for their safety. - Young children should be kept away from the appliance and supervised to ensure that they do not play with it. GAS CONNECTION WARNING • • This operation must be performed by a qualified technician. The gas supply system must comply with local regulations. You can find specific local regulations for some countries in the paragraph “Reference to Local Regulations”. If no information concerning your Country is given, please ask details to your Installer. • The connection of the hob to the gas pipe network or gas cylinder must be made by means of a rigid copper or steel pipe with fittings complying with local regulations, or by means of a continuous-surface stainless steel hose complying with local regulations. The maximum length of the hose is 2 linear metres. • Connect elbow (A)* or (B)* supplied with to the hob inlet main pipe and interpose the washer (C) supplied, in compliance with EN 549. Remove the information label and keep it with the instructions booklet. Use pressure regulators suitable for the gas pressure indicated in the Instruction. • The gas nozzles must be changed by After Sales Service or a qualified technician. • Nozzles not supplied with the appliance must be ordered from After Sales Service. • Adjust the minimum setting of the taps. NOTE: when liquid petroleum gas is used (G30/G31), the minimum gas setting screw must be tightened as far as it will go. IMPORTANT: should you experience difficulty in turning the burners knobs, please contact the After Sales Service for the replacement of the burner tap if found to be faulty. TROUBLESHOOTING GUIDE If the hob will not operate correctly, before calling the After-Sales Service, refer to the Troubleshooting Guide to determine the problem. The burner fails to ignite or the flame is not even Check that: • The gas or electrical supplies are not shut off and especially that the gas supply tap is open. • The gas cylinder (liquid gas) is not empty. • The burner openings are not clogged. • All the burner parts have been positioned correctly. [. . . ] Do not leave acid or alkaline substances, such as vinegar, mustard, salt, sugar or lemon juice on the hob. Grids, burner caps and burners can be removed to be cleaned. max. NATURAL GAS (Methane) G25 LIQUEFIED PETROLEUM GAS (Butane) G30 (Propane) G31 Semi-rapid Auxiliary 4 ring Semi-rapid Auxiliary 20 25 30 25 30 35 Type of gas used G25 25 mbar G30/G31 30 mbar Model configuration 3 burners 3 burners Rated thermal flow rate (kW) 6. 15 6. 15 Total rated consumption 683 l/h 447 g/h Air required (m3) for burning 1 m3 of gas 8. 187 30. 94 HOW TO USE THE HOB WARNING Do not let the burner flame extend beyond the edge of the pan. ELECTRIC SUPPLY: 230 V ~ 50 Hz IMPORTANT: WHEN THE HOB IS IN USE, THE ENTIRE HOB AREA MAY BECOME HOT. • To ignite one of the burners, turn the relative knob anti-clockwise to the maximum flame setting. [. . . ]