User manual WHIRLPOOL TGZ 3405-1 WS PROGRAM CHART

[. . . ] Do not repair or replace any part of the appliance unless specifically stated in the user manual. TECHNICAL INFORMATION FOR THE INSTALLER • • This product can be embedded in a worktop 20 to 60 mm thick. If there is no oven beneath the hob, insert a separator panel that has a surface at least equal to the opening in the work surface. This panel must be positioned at a maximum distance of 150 mm below the upper surface of the work surface but, in no case less than 20 mm from the bottom of the hob. In the case that you intend to install an oven beneath the hob, make sure that it is manufactured by Whirlpool and equipped with a cooling system. [. . . ] - Do not touch the appliance with any wet part of the body and do not operate it when barefoot. - This hob (class 3) is designed solely for private household use for cooking food. Do not use this appliance as a space heater to heat or warm the room. Doing so may result in carbon monoxide poisoning and overheating of the hob. The Manufacturer declines all responsibility for inappropriate use or incorrect setting of the controls. - The appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or with lack of experience and knowledge of the appliance, unless supervised or previously instructed in its use by those responsible for their safety. - Young children should be kept away from the appliance and supervised to ensure that they do not play with it. GAS CONNECTION WARNING • • This operation must be performed by a qualified technician. The gas supply system must comply with local regulations. You can find specific local regulations for some countries in the paragraph “Reference to Local Regulations”. If no information concerning your Country is given, please ask details to your Installer. • The connection of the hob to the gas pipe network or gas cylinder must be made by means of a rigid copper or steel pipe with fittings complying with local regulations, or by means of a continuous-surface stainless steel hose complying with local regulations. The maximum length of the hose is 2 linear metres. Remove the information label and keep it with the instructions booklet. Use pressure regulators suitable for the gas pressure indicated in the Instruction. • The gas nozzles must be changed by After Sales Service or a qualified technician. • Nozzles not supplied with the appliance must be ordered from After Sales Service. • Adjust the minimum setting of the taps. NOTE: when liquid petroleum gas is used (G30/G31), the minimum gas setting screw must be tightened as far as it will go. IMPORTANT: should you experience difficulty in turning the burners knobs, please contact the After Sales Service for the replacement of the burner tap if found to be faulty. Regulation for room ventilation NOTE: if the appliance is not equipped with safety devices on the burners (thermocouples), the air vents must be increased by 100%, and must be at least 200 cm2), in compliance with M. D. Connection to gas supply Before connecting the appliance, make sure that the gas supply system complies with standards UNI-CIG 7129 and UNI-CIG 7131. Gas connection The connection to the mains gas network or gas cylinder must be made using a rigid copper or steel pipe with fittings complying with standards UNI-CIG 7129, or using a continuous-surface stainless steel hose complying with standards UNI-CIG 9891. The pressure control valves to be used must comply with the UNI EN 12864 standard for gas cylinders and the UNI EN 88 standard for piped methane gas. AFTER-SALES SERVICE Before calling the After-Sales Service, make sure you can give the following information: - type of fault or problem; - exact model (written on the label affixed to the instruction/warranty); - service number that follows the word SERVICE on the rating plate under the hob and on the label affixed to instruction/warranty; - your complete address and phone number. If any repairs are required, please contact an authorised After-Sales Service, as indicated in the warranty. TROUBLESHOOTING GUIDE If the hob will not operate correctly, before calling the After-Sales Service, refer to the Troubleshooting Guide to determine the problem. [. . . ] - Two burners simultaneously for one receptacle (e. g. fish kettle). INJECTORS TABLE Burner Ultra-rapid Semi-rapid Auxiliary CATEGORY II2H3+ Injector marking Rated thermal Rated flow rate consumption kW Ultra-rapid 136 95 78 94 67 50 94 67 50 3. 50 1. 65 1. 00 3. 50 1. 65 1. 00 3. 50 1. 65 1. 00 333 l/h 157 l/h 95 l/h 254 g/h 120 g/h 73 g/h 250 g/h 118 g/h 71 g/h Pot Ø From 24 to 26 cm From 16 to 22 cm From 8 to 14 cm Type of gas used Type of burner Reduced heat capacity kW 0. 60 0. 35 0. 30 0. 60 0. 35 0. 30 0. 60 0. 35 0. 30 Gas pressure mbar min. max. NATURAL GAS (Methane) G20 LIQUEFIED PETROLEUM GAS (Butane) G30 LIQUEFIED PETROLEUM GAS (Propane) G31 Semi-rapid Auxiliary Ultra-rapid Semi-rapid Auxiliary Ultra-rapid Semi-rapid Auxiliary 17 20 25 20 28-30 35 HOW TO USE THE HOB WARNING Do not let the burner flame extend beyond the edge of the pan. 25 37 45 Type of gas used IMPORTANT: WHEN THE HOB IS IN USE, THE ENTIRE HOB AREA MAY BECOME HOT. • To ignite one of the burners, turn the relative knob anti-clockwise to the maximum flame setting. [. . . ]