User manual WHIRLPOOL TLS 12 PROGRAM CHART

[. . . ] For improved garment care, spin speed is restricted in these programmes. Programme Care Labels Detergents and Additives PreMain Softener wash Wash Start Eco delay Avvio Eco ritardato i 2) i Special options Max. PreEasy Intensive Rinse Variable Spin Speed wash ironing rinse hold spin PreStiro Risciacquo Esclusione Centrirpm lavaggio facile intensivo centrifuga fuga i i i i i 1200 Cotton 40 - 60 - 95 °C Synthetics 30 - 40 - 60 °C Delicates 30 - 40 °C Daily load 40 °C Quick wash 30 °C Wool Cold - 40 °C Handwash 30 - 40 °C Rinse & Spin Spin Gentle Spin Drain Cotone 40 - 60 - 95°C Sintetici 30 - 40 - 60°C Delicati 30 - 40°C Misti 40°C Rapido Lana Freddo - 40°C Lavaggio a mano 30 - 40°C Risciacquo & Centrifuga Centrifuga Centrifuga breve Scarico – – – – 5. 0 2. 5 i Yes 1) i i 2) i i i i i i 1000 3) 1. 5 i Yes 1) i i 2) – i – – i i 1000 3) 3. 0 Slightly to normally soiled textiles made of cotton and/or synthetics. Shortly worn outer clothing made of cotton, polyester, polyamide and blends with cotton. Only woollens with a felt-free finish, labelled with the woolmark and identified as machine washable. [. . . ] PROGRAMME START Open the tap and press the “Start/Pause” button. The indication lamp next to the “Start/Pause” button lights up. The programme sequence indicator shows the current programme phase, running from left to right through Wash, Rinse, Spin/Drain. When the programme phrase is finised, the corresponding indication goes out. • Note: If there is a power interruption or if the appliance is disconnected during the cycle, the programme will run again from the point where it was interrupted. “DOOR OPEN” INDICATION Before starting and after end of a programme, the lamp lights to show the the lid can be opened. As long as a wash programme is running, the lid remains locked and must on no account be forced open. In case you have an urgent need to open it during a running programme, refer to “Cancel (Reset) a running programme before the end”. RED INDICATIONS “Service” Lighting up of the “Service” indication can be caused by a fault in an electrical component. Refer to the “Troubleshooting Guide” in your “Instructions for Use”; if the fault persists, contact our After Sales Service. “Water tap closed” The appliance has no or insufficient water supply. Open the water tap: if the indications still lights up, refer to the “Troubleshooting Guide” in the Instructions for Use. “Clean pump” Waste water is not pumped out. Check whether the drain hose is kinked or the filter must be cleaned: in the latter case refer to the Instructions for Use (“Removing the Filter”). PROGRAMME END • All the lights of the programme sequence indicator are off, and the “Door open” indication lights up. Turn the programme selector to the “Off/O” position. Open lid and drum and unload the machine. Leave the lid open for some time to allow the interior of the machine to dry. CHANGE PROGRAMME AND/OR OPTIONS AFTER PROGRAMME START 1. Press the “Start/Pause” button to pause the programme. Select the new programme, any options and another spin speed if you want. Press the “Start/Pause” button again. The new programme continues at the same position where the previous programme was interrupted. [. . . ] “Intensive rinse” button • The amount of water is increased to ensure a more intensive rinse. • This option is particularly suitable for areas with very soft water, washing baby linen and people with skin allergies. “Rinse hold” button • The laundry remains in the last rinse water without progressing to the final spin cycle to avoid creasing and prevent colours from changing. • This option is particularly recommended for the “Synthetics”, “Daily load” and “Delicates” programmes. [. . . ]