User manual WHIRLPOOL UMC5200BCB-W-S 12-07

[. . . ] This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING. " These words mean: DANGER WARNING You can be killed or seriously injured if you don't immediately follow instructions. You can be killed or seriously injured if you don't follow instructions. All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed. W10308503A INSTALLATION INSTRUCTIONS Tools and Parts Tools Needed Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here. Minimum Cutout Dimensions 23³/" (60. 3 cm) 1/" (4. 0 cm) Measuring tape Pencil Phillips screwdriver Drill 7/64" drill bit Tape 16/" (42. 9 cm) 25" (63. 5 cm) htdiW A ¹¹/" Parts Supplied 3" (7. 6 cm) (1. 8 cm) B Duct base Trim kit frame A. [. . . ] 3" (7. 6 cm) minimum dimension is from lower oven cutout ceiling to microwave oven cutout floor. Trim kit frame extends 11/16" (1. 8 cm) below, and 1/" (4. 0 cm) above the cutout opening. 13/16" screws (2) 9/16" screws (16) 1/2" screws (4 - painted) Trim Kit Frame Dimensions 26/" (6 8. 3 cm)* 29³/" (7 5. 6 cm)* * Location Requirements The microwave oven may be installed over a built-in oven. If installing over a built-in oven, make sure there is a minimum of 3" (7. 6 cm) between the top of the lower oven cutout and the microwave oven cutout floor. The microwave oven may also be installed in a cabinet by itself (without a built-in oven below). For best usability, we recommend a minimum distance of 36" (91. 4 cm) from the floor to the cutout floor. Make sure the surrounding cabinetry has clearance to open and close freely. Allow a clearance of at least 1" (2. 5 cm) below the cutout floor (3" [7. 6 cm] for installation above a built-in oven), and a clearance of at least 2" (5. 1 cm) above the cutout opening. 19¹/" (48. 6 cm) 1/" (3. 7 cm)* 2/" (7. 3 cm)** 24" (61. 0 cm) /" (2. 2 cm) 3" (7. 6 cm) A 2" (5. 1 cm) 2" (5. 1 cm) *27" (68. 6 cm) trim kit **30" (76. 2 cm) trim kit B 1" (2. 5 cm) B 3" (7. 6 cm) C D E A. Floor 36" (91. 4 cm) 2 Electrical Requirements Microwave Oven Preparation 1. Unplug microwave oven before proceeding with installation. Remove any loose items inside microwave oven. WARNING Duct Assembly 1. Using 7/64" drill, drill pilot hole into hole center marked in Step 2. 3 4. Install the 3/16" screw, and leave 1/8" (3. 2 mm) to 3/16" (4. 7 mm) protruding from the cutout floor. A B ¹/" (3. 2 mm) (min) ³/" (4. 7 mm) (max) NOTE: If Template 2 is missing or unusable, measure straight up from upper end holes on bottom bracket, and mark the new holes at 12¹/" (32. 9 cm) and 15²¹/" (39. 8 cm). Make sure the bottom bracket end holes and the new holes on each side are plumb. CD TEMPLATE 2 DC DC 12¹/" (32. 9 cm) 15²¹/" (39. 8 cm) CD A. Slide microwave oven partway into cutout opening. WARNING BA AB Electrical Shock Hazard Plug into a grounded 3 prong outlet. Failure to follow these instructions can result in death, fire, or electrical shock. 6. Make sure microwave oven is centered in the opening, and slide it into place, engaging the 3/16" screw and duct base. 5. Using 7/64" drill, drill pilot holes into the cabinet through holes marked in Step 4, then remove template. Position top bracket over pilot holes drilled in Step 5, then secure with four 9/16" screws. (Illustration in this step shows 30" [76. 2 cm] installation. ) A B C D A. Bottom bracket Install Top and Bottom Brackets 1. [. . . ] Bottom bracket Install Top and Bottom Brackets 1. Align bottom bracket to duct base, and mark 7 mounting holes of bottom bracket, as shown. 30" (76. 2 cm) Install Trim Kit Frame 1. Position trim kit frame against the top and bottom brackets. [. . . ]