User manual WHIRLPOOL W8TXNGZBT USE & CARE GUIDE

[. . . ] · This unit requires connection to a grounded (threeprong), polarized receptacle that has been placed by a qualified electrician in accordance with applicable electrical codes. Safety Alert Definitions Safety items throughout this guide are labeled with a Danger, Warning or Caution based on the risk type: DANGER Danger means that failure to follow this safety statement will result in severe personal injury or death. WARNING Warning means that failure to follow this safety statement could result in serious personal injury, or death. CAUTION Caution means that failure to follow this safety statement may result in minor or moderate personal injury, property or equipment damage. www. U-LineService. com 2 08/2006 2175R Refrigerator and 2175RF Refrigerator/Freezer General Precautions Use this appliance for its intended purpose only and follow these general precautions along with those listed throughout this guide: 2 Inspect and Plan You have received a carton containing your 2175R Refrigerator or 2175RF Refrigerator/Freezer with a package inside containing a Use & Care Guide and a Product Registration Card. Complete and mail the Product Registration Card or register online at www. U-LineService. com. Once your unit is installed, keep the Use & Care Guide and this Installation Guide in a safe place for future reference. Your unit is Black, White or Stainless Steel. [. . . ] · For best performance and life outdoors, place under a counter or provide shelter of some kind. · In climates where high humidity and dew points are present, condensation may appear on outside surfaces. The condensation will disappear when the humidity drops. Figure 9 www. U-LineService. com 6 08/2006 2175R Refrigerator and 2175RF Refrigerator/Freezer Side-By-Side Installation Instructions For a complete refreshment center, install your 2175R or 2175RF Model beside a U-Line Ice Maker, Combo or Wine Captain Model (see Figure 11 for typical cut-out). Note that each Side-By-Side Installation will be different. · Cut-out width for a side-by-side installation is the total of the widths listed under Cut-Out Dimensions in each unit's Installation Guide. For example: Placing a 2175R or 2175RF next to a 2115 series unit would require a cut-out width of: 24-3/16" + 15-3/16" = 39-3/8" Placing a 2175R or 2175RF next to a 2175 series unit would require a cut-out width of: 24-3/16" + 24-3/16" = 48-3/8" · No trim kit is required. However, 1/4-inch space needs to be maintained between the units to ensure unobstructed door swing. · Units must operate from separate, properly grounded electrical receptacles placed according to each unit's Electrical Specifications. Typical Side-By-Side Cut-Out 4 Prepare and Install Door Panel (Black and White Units Only) Two types of custom door panels can be installed on your Black or White unit to harmonize with or accent the surrounding décor: a Custom 1/4" Insert or a Full Overlay. If no custom door panel is used, go on to 5 Adjust Door. Custom 1/4'' Door Panel Insert Door Panel Preparation A custom door panel can be inserted into the doorframe. Custom door panels can be flat or raised, as long as the maximum panel thickness where inserted into the door reveal (channel) is 1/4"-thick. For raised panels, the depth of the reveal is 1/4" on all four sides. IMPORTANT Raised panels will reduce the door's 90° swing/zero clearance if the unit is installed next to a wall or similar type of structure. Remove the existing bottom pivot plate and replace with the Full Overlay pivot plate (see Figure 22). Existing Door Drill ø 5/32" x 3/8" Deep 7 Places Model 2175 6 places Model 2115 and CLR2160 For use with #10 x 5/8" Wood Screw and Nylon Spacer 15-9/16" ± 1/4" Existing Bottom Pivot Plate (Remove and Discard) Wood Panel Bottom Pivot Plate (5/8" Longer Than Existing Bottom Pivot Plate, Flush Side Facing Out) #8-32 x 3/8" SEMS Hex Screw Two Places Figure 22 28-7/8" ± 1/4" IMPORTANT Door panel and overlay panel must be aligned properly or the door will not operate correctly. Assembling the Door 1" 11-7/8±1/32 For use on Model 2175 Only 1" ULIN_0402_A 1. Install the assembled panel by sliding the original door panel back into the doorframe. Replace the Overlay Handle and secure with the two screws removed in Step 4 under Removing Existing Door. Attach Overlay cap to door, opposite side of where hinges will be (see Figure 23). Overlay Cap Figure 20 3. Attach the door panel to the overlay panel using #10 x 5/8" wood screws and nylon spacers. The nylon spacers fit between the overlay panel and the door panel as shown in Figure 21. The spacers allow the original door panel to slide back into the 1/4"-thick door reveal (channel). 3/4" Wood Panel Replacement Handle Figure 23 www. U-LineService. com 10 08/2006 2175R Refrigerator and 2175RF Refrigerator/Freezer 4. Attach Top Pivot Plate to door handle, on side where hinges will be. Use the two #8-32 x 1/2" Flat Head Phillips screws (Black) supplied with kit (see Figure 24). #8-32 x 1/2" Flat Head Screws Black, Two Places 3/4" Wood Overlay Top Pivot Plate Screw to attach Handle Removed in step 4 Door Closure Top Boss Existing Door Door Closure Bottom Boss Pivot Post #8-32 x 1/2" Flat Head Screw Three Places Wood Panel Bottom Hinge Plate (5/8" Longer than Existing Bottom Hinge Plate) Figure 24 Figure 26 5. Starting at the corners and working toward the center, push the door gasket back into place. [. . . ] · Never use an extension cord to connect power to the unit. Go on to 7 Level the Unit. Installation Tip If the room floor is higher than the floor in the cut-out opening, adjust the rear feet to achieve a total unit rear height of 1/8" less than the opening's rear height. Shorten the unit height in the front by adjusting the front feet. This allows the unit to be gently tipped into the opening. [. . . ]