User manual WHIRLPOOL WA CARE 714 SD INSTRUCTION FOR USE

[. . . ] This programme eliminates bacteria, ensuring sanitization of your laundry. Normally to heavily soiled bed linen, table linen and underwear, towels, shirts etc. Normally soiled cotton jeanswear and garments made of robust jeanslike material such as trousers and jackets. Normally soiled garments made of artificial fibres (like polyester, polyacryl, viscose etc. ) or their blends with cotton. ❉ ❉ ❉ ❉ ❉ — — — — — — — Yes ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ — — — ❉ ❉ ❉ — — — — — — — — ❉ ❉ ❉ ❉ ❉ — — — — — — — ❉ ❉ — ❉ — ❉ — — ❉ ❉ — — ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ — — ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ — ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ max. Yes max. Yes max. Yes max. 30 - 40 °C Curtains and delicate clothing, dresses, skirts, shirts and blouses. Yes 1000 1) 4. 0 40 °C 3. 0 30 °C / - 40 °C 40 - 60 °C 7. 0 1. 0 Lightly to normally soiled robust laundry made of cotton, linen, artificial fibres and their blends. [. . . ] However, intermediate spin phases remain during rinse. to start draining. FAILURE INDICATORS If one of the failure indicators blinks, consult the “Troubleshooting Guide” in your Instructions for Use. “Water tap closed”: no or not sufficient inlet water. “Service”: failure or malfunction of an electrical component. “Clean pump”: waste water is not pumped out. PROGRAMME END START DELAY The “Start delay” allows to run the machine at the consumer’s 1. convenience, for example at night when electricity is cheaper. Do not use liquid detergent when activating “Start delay”. • Select programme, temperature and options. Press the “Start delay” button to select a delay time of 1, 3, 6, 9 or 12 hours. • • • Press the “Start/Pause” button . The delay time indicator goes off when the programme starts and it is replaced by the programme flow bar indication. Once having pressed the “Start/Pause” button , the delay 2. : time can be changed by pressing again the “Start delay” button. To cancel the “Start delay” . . . before you press the “Start/Pause” button • the “Reset” button . : Turn the programme selector to another position or press • • The “Door open” indicator shows “End”. Turn the programme selector to the “Off/O” position. Leave the door ajar to allow the drum to dry . lights up, and the display Consumption values were measured in normalized conditions, in compliance with IEC/EN 60456. In the home, they may vary depending on the individual water supply pressure and temperature, the load and the type of wash. The consumption data indicated are based on an inlet water temperature of approx. 15°C through the cold fill valve as well as the hot fill valve (if available). If your washing machine has a hot fill valve, connection of this valve to hot water supply will lower the energy consumption by reduced heating times, depending on the individual hot fill inlet water temperature. [. . . ] • Press the “Start/Pause” button delay disappears from the display. • SELECT ANY DESIRED OPTION Push the button of any option desired - the indicator lights up. If the combination programme/option or option/option is not possible, the indicator switches off automatically. “Rapid” button • • Enables quicker washing by shortening the programme duration. [. . . ]