User manual WHIRLPOOL WA KOMFORT 1400 PROGRAM CHART

[. . . ] the woolmark and identified as machine Textiles made of linen, silk, wool or viscose marked as – – – – – ❉ – – ❉ – – – – ❉ Wool Wolle – – ❉ – – ❉ Dessous / Handwash Dessous / Handwäsche 1. 0 “handwashable”. This cycle is particularly suitable to treat delicate lingerie (use of a laundry net strongly recommended). Normally soiled blouses, shirts and other outer clothing 3. 0 made of polyester (Diolen, Trevira), polyamide (Perlon, Nylon) or mixtures of these fibres with cotton. Easy ironing Leicht bügeln Spin Schleudern – – – – 20 6. 0 6. 0 – – – – – – – – – – ❉ – – – – – – – ❉ Rinse & Spin Spülen & Schleudern Drain Abpumpen 1) 2) – – – – For improved garment care spin speed is restricted to 1000 rpm in this programme. For improved garment care spin speed is restricted to 400 rpm in this programme. Black process 45. 0° 100. 0 LPI { ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ I G. [. . . ] By pressing the Start Delay button again after the “24” setting, the time delay can be deleted again or set again. After “Start” has been pressed: The preset number of hours can be reduced by pressing the “Start Delay” button again; please note, however, that the washing programme starts IMMEDIATELY, as soon as you operate it again with the Start Delay switch 01 setting. To increase the number of hours preselected, first turn the programme selector switch to the “Off” position. Then set the programme and the additional options again and select the desired number of hours. PROGRAMME START After you have selected the programme and the additional option, the indicator light over the “Start” button flashes. Turn on the tap and start the programme by pressing the “Start” button. Now the indicator light above the button goes on. In addition, all programme phases are indicated by the associated lights. After the end of a programme phase, the associated indicator light goes out. Thus the programme sequence indicator moves from left to right across the wash, rinse and spin phases. At the end of the programme, only the “End” indicator is still on. “DOOR LOCKED” INDICATOR As long as a washing programme is running, the lamp lights up to show that the door cannot be opened. When the lamp goes off, the door can be opened again. The consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60456. The programme duration may also vary from the chart values. The washing machine is able to allow for particular household conditions and to adapt the programme run time accordingly. *** To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out. **** Reference programme for energy label. POUR IN DETERGENT, CLOSE THE DOOR AND SELECT A PROGRAMME Add the detergent as described in the chapter “Detergent and Additives” in the instructions for use. Turn the programme selector knob to the desired programme and temperature. The remaining time display shows the duration of the chosen programme (in hours and minutes), and the lamp over the “Start” button flashes. The programme sequence indicator and the predefined spin speed indication corresponding to the selected programme lights up. USING CHLORINE BLEACH • Wash your laundry in the desired programme (Cotton, Synthetics), adding an appropriate amount of chlorine bleach to the SOFTENER chamber (close the detergent dispenser carefully). • Immediately after end of programme, start the “Rinse and Spin” programme to eliminate any residual bleach smell; if you want, you can add softener. [. . . ] Set the programme selector knob to the “Off” position. RESELECT AFTER PROGRAMME START A newly-selected programme will continue in the same programme section during which the current programme was interrupted. Therefore do not add any more detergent. Press the “Start” button to interrupt the programme. [. . . ]