User manual WHIRLPOOL WA PRIMELINE 24TDI PROGRAM CHART

[. . . ] To avoid noise of spinning at night, set spin speed to “0” and start spin programme in the morning, or define programme start with “Start delay” accordingly. Normally soiled blouses, shirts, overalls etc. made of polyester (Diolen, Trevira), polyamide (Perlon, Nylon) or blends with cotton. Start Detergents and additives Special options Spin PreMain Softener Clean + Pre- Rinse Intensive Easy delay Variable Max wash hold rinse ironing spin wash wash Spin Clean + VorSpül- Intensiv Leicht Start- Schleu- Speed wäsche stopp spülen bügeln vorwahl dern rpm White Cotton / Hygienic + Coloured Cotton Buntwäsche 70 - 95 °C 50 - 60 °C 20 - 40 °C 6. 0 6. 0 5. 0 6. 0 ❉ ❉ ❉ ❉ ❉ ❉ ❉ 2) ❉ max. SuperEco SuperEco 20 - 60 °C — Yes 3) ❉ — — ❉ ❉ — ❉ 2) ❉ max. Synthetics Daily load Quick wash Jeans Delicates Wool Lingerie / Handwash Rinse & Spin Spin Gentle Spin Drain Pflegeleicht Mischwäsche 20 - 60 °C 2. 5 3. 0 3. 0 5. 0 1. 5 1. 0 1. 0 ❉ — — ❉ ❉ — — — — — — Yes 3) Yes Yes Yes Yes 3) 3) ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ — — — ❉ — — ❉ — — — — — — — ❉ — — ❉ ❉ — — — — — — ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ — — — ❉ ❉ — — — — — ❉ — — — ❉ ❉ — — — — — — — — — ❉ 2) ❉ 2) ❉ 2) ❉ ❉ 2) 2) ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ — 1000 1) max. 1000 1) — 20 - 60 °C Slightly to normally soiled textiles made of cotton and/or synthetics. [. . . ] If you want to replace the saved programme setting by another one: • Push the programme button, select temperature, spin speed and options as desired and then press and hold the “Favourites” button for at least 3 seconds. The previously saved programme setting will be replaced by the new one. “DOOR OPEN” INDICATION Before starting and after end of a programme, the lamp lights to show that the door can be opened. As long as a wash programme is running, the door remains locked and must on no account be forced open. In case you have an urgent need to open it during a running programme, refer to “Cancel (Reset) a running programme before the end”. RED INDICATIONS “Service” Lighting up of the “Service” indication can be caused by a fault in an electrical component. Refer to the “Troubleshooting Guide” in your Instructions for Use; if the fault persists, contact our After Sales Service. “Water tap closed” The appliance has no or insufficient water supply. Open the water tap; if the indication still lights up, refer to the “Troubleshooting Guide” in your Instructions for Use. “Clean pump” Waste water is not pumped out. Check whether the drain hose is kinked or the filter must be cleaned; in the latter case refer to the Instructions for Use (“Removing the Filter”). Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash. The time indicated on the display can deviate from the values in the table, because it takes into account the household * conditions applicable at that time. To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out. ** *** Reference Programme for Energy Label. START DELAY The “Start Delay” allows to run the machine at the consumer’s convenience, for example at night when electricity is cheaper. Do not use liquid detergent when activating the “Start Delay”. • Select programme, temperature and options. • Press the “Start Delay” button to select the delay time by 1 to 23 hours; • Press the “Start/Pause” button. The indication light over the “Start Delay” button starts blinking, and the countdown of the delay time begins. During the whole countdown, the light of the “Start Delay” button as well as the dot on the display keep blinking. • The time delay indication disappears when the programme starts and it is replaced by the remaining programme time. • Once having pressed the “Start/Pause” button, the number of hours preselected can be reduced by pressing and holding the “Start Delay” button. From 1 hour on, the delay time can also be reduced in steps of 10 minutes. To cancel the “Start Delay” . . before you press the “Start/Pause” button: • Turn the programme selector to another position or press the “Reset” button. [. . . ] • This option is particularly suitable for areas with very soft water, washing baby linen and helps people with allergies. “Easy ironing” button • Can be used together with “Cotton”, “Synthetics” and “Daily load” programmes to make ironing easier. • Increases the water quantity and the clothes are spun very gently. “Variable spin” button • Every programme has a predefined spin speed. [. . . ]