User manual WHIRLPOOL WA PURE XL 34 FLDD PROGRAM CHART

[. . . ] max. 2. 0 This programme (40°C) is tested and approved by The Woolmark Company for machine washable wool. Textiles made of silk, linen, wool and viscose marked as “handwashable”. 2. 0 This programme (40°C) is tested and approved by The Woolmark Company for handwashable wool. programme is particularly 2. 0 Thisstrongly recommended). suitable to treat delicate lingerie (use of a laundry net Dessous Jeans Sport 20 - 30 °C 20 - 60 °C 20 - 30 °C 7. 0 Normally soiled cotton jeanswear and garments made of robust jeanslike material such as trousers and jackets. [. . . ] • Select programme, temperature, spin speed and options. • Press the Start delay button to select one of the delay time steps between 0:30 and 23:00 hours. • Press the “Start (Pause)” button; the light stops blinking and becomes solid. The countdown of the delay time begins; the clock symbol next to the delay time and the colon between hours and minutes blink. • The time delay indication disappears when the programme starts and it is replaced by the remaining programme time. To cancel the “Start delay” . . before you press the “Start (Pause)” button: • Press the “Reset” button, or set the start delay time to “0:00” the delay time disappears after a few seconds. . . after having pressed the “Start (Pause)” button: Press the “Start (Pause)” button - the delay time disappears from the display; press “Start (Pause)” again to start the selected programme immediately. RED FAILURE INDICATIONS If one of the red failure indications on the display lights up, refer to the “Troubleshooting Guide” in your “Instructions for Use”. PROGRAMME END • 1. The display shows “End”, and the “Door open” indication lights up. Turn the programme selector to the “Off/O” position. Open the door and unload the machine. Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash. The time indicated on the display can deviate from the values in the table, because it takes into account the operation conditions * applicable at that time. To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out. ** *** Reference Programme for Energy Label (with separator in detergent dispenser removed for use of powder detergent). “Rinse hold” button • Leave the door ajar to allow the drum to dry. • If you do not turn the programme selector to the “Off/O” position, all lights of the control panel go out after a few minutes to save energy - only “End” will remain on the display. ADD DETERGENTS, CLOSE THE DOOR AND SELECT THE PROGRAMME • The laundry remains in the last rinse water, without progressing to the fnal spin cycle, to avoid creasing and prevent colours from changing. • The programme stops to “Rinse hold” when the “Rinse hold” symbol on the display blinks; the light of the “Start (Pause)” button blinks as well. • To terminate the “Rinse hold” by draining the water, without any spinning, press the “Start (Pause)” button. • To terminate the “Rinse hold” by spinning the laundry, press the "Variable spin" button to select the desired spin speed and then “Start (Pause)” to start the spin cycle. • Do not leave the laundry to soak for too long in the “Rinse hold”. “Intensive rinse” button • More water is added and rinse cycle is prolonged. • This option is particularly suitable for areas with very soft water or for washing baby linen, and helps people with allergies. [. . . ] “Prewash” button • Only for heavily soiled loads (for example sand, granular dirt) sensible. Increases the cycle time by approximately 15 min. • Do not use liquid detergent for the main wash when activating the “Prewash” option. CHANGE PROGRAMME AND/OR OPTIONS AFTER PROGRAMME START 1. Press the “Start (Pause)” button to pause the programme. [. . . ]