User manual WHIRLPOOL WAB 1211 SW INSTRUCTION FOR USE

[. . . ] 40115310GB. fm Page 1 Friday, June 3, 2011 10:41 AM DEFINITION OF USE This appliance is exclusively destined to wash and spin machine washable laundry in quantities which are usual for private households. • Observe the instructions given in these Instructions for Use and in the separate Programme Chart when using the washing machine. • Keep these Instructions for Use and the Programme Chart; if you pass on the washing machine to another person, also give him/her the Instructions for Use and the Programme Chart. BEFORE USING THE WASHING MACHINE 1. Remove the packaging and check • After unpacking, make sure that the washing machine is undamaged. If in doubt, do not use the washing machine. [. . . ] 6. Lay the hose in the cover, fold the cover up and close it using the detergent dispenser insert or a coin. 7. Pour about 1 l of water into the detergent dispenser to reactivate the Eco System. You must also put the plug back into the socket. 8. You can now load the washing machine and start the desired programme. 1 5 6 6 Black process 45, 0° 130, 0 LPI 40115310GB. fm Page 8 Friday, June 3, 2011 10:41 AM CARE AND MAINTENANCE Appliance exterior and control panel • Clean using a neutral household detergent and a damp cloth (do not use abrasive products or solvents). • Dry with a soft cloth. Door seal • Clean occasionally with a damp cloth. • Check the seal folds for foreign bodies periodically. Filter Appliance interior • If you never or seldom wash your laundry at 95°C, we recommend to occasionally run a 95°C programme without laundry, adding a small amount of detergent, to keep the interior of the appliance clean. • Leave the door and the detergent dispenser open for some time after each washing so that the interior can dry. • Check and clean the filter regularly, at least two or three times a year (see “Cleaning The Filter”). Water supply hose • Check the hose regularly for brittleness and cracks and replace it if necessary using a new hose of the same type (available from After-Sales Service or specialist dealer). Do not use flammable fluids for cleaning the appliance. Detergent dispenser Clean the dispenser drawer and the dispenser compartment regularly, at least three or four times a year, to prevent detergent build-up. 1. Press the release lever in the prewash compartment down and pull out the dispenser (see downward arrow). 2. Remove the inserts from the detergent dispenser (see upward arrows). 4. Replace the separate parts in the detergent dispenser and slide the dispenser back into the dispenser compartment. Periodically check and clean the mesh filters in the water connection. 1. Turn off the tap. 2. Unscrew the water inlet hose from the tap. 4. Screw the supply hose back onto the tap. 5. Unscrew the supply hose from the washing machine. 6. Clean the mesh filter in the washing machine. 7. Screw the supply hose back on to the machine. 8. Turn on the tap and ensure that the connections are water-tight. Black process 45, 0° 130, 0 LPI 40115310GB. fm Page 9 Friday, June 3, 2011 10:41 AM TROUBLESHOOTING GUIDE This washing machine is equipped with automatic safety functions which detect and diagnose faults at an early stage and react appropriately. Often, however, the faults detected are small enough to be solved in a matter of minutes. For example: The appliance vibrates during the spin cycle. Check whether: • The appliance is levelled and solidly installed on all four feet (see “Installation”). • The transit bolts have been removed. Before using the washing machine you must remove the transit bolts (see “Installation”). The appliance will not start; no lamp lights up. Check whether: • The appliance is plugged in. • The wall socket is functioning correctly (use a table lamp or similar to test). • The washing machine is switched on. Final spin results are poor: The appliance has an imbalance detection and correction system. [. . . ] Screw the plywood sheet to the floor. Black process 45, 0° 130, 0 LPI 40115310GB. fm Page 14 Friday, June 3, 2011 10:41 AM Connect the water supply hose(s) (A or B, depending on the model) • If your washing machine has one inlet hose and one inlet valve on the back: connect to cold water supply only. • If your washing machine has two inlet hoses and two inlet valves on the back: connect to cold and hot water supply, or to cold water supply only by using the Y-piece connector. Both inlet valves must be connected to the water supply. Observe the detailed instructions in your programme chart. [. . . ]