User manual WHIRLPOOL WAK 7780/1 INSTRUCTION FOR USE

[. . . ] 4gb15170. fm5 Page 3 Thursday, July 11, 2002 11:35 AM ENGLISH ESPAÑOL PORTUGUÊS ITALIANO ü

ù Instructions for use Instrucciones para el uso Manual de utilização Istruzioni per l’uso /0"$! " Page 5 Página 19 Página 32 Pagina 45 0/.  Black Process Plate 4 4gb15170. fm5 Page 4 Thursday, July 11, 2002 11:35 AM Black Process Plate 4gb15170. fm5 Page 5 Thursday, July 11, 2002 11:35 AM Contents Before Using The Washing Machine Precautions and General Recommendations Description Of The Washing Machine Door Child Safety Before The First Wash Cycle Preparing The Wash Detergent And Additives Removing The Filter Draining Residual Water Care And Maintenance Troubleshooting Guide After-Sales Service Transport/Handling Electrical connection Black Process Plate 4gb15170. fm5 Page 6 Thursday, July 11, 2002 11:35 AM Before Using The Washing Machine 1. Remove the packaging and check • After unpacking, make sure that the washing machine is undamaged. If in doubt, do not use the washing machine. Contact After-Sales Service or your local retailer • Check that the accessories and supplied parts are all present • Keep the packing material (plastic bags, polystyrene parts, etc. ) out of reach of children, as they are potentially dangerous 4. [. . . ] Now unscrew the filter completely and remove it. Clean the filter and the filter chamber. Insert the filter with the guide pin upwards and screw it in clockwise to the stop (handle horizontal). Pour about 1 litre of water into the detergent drawer to reactivate the Eco system. Check that the foreign body trap is seated properly and tightly in place. Remove the inserts (the siphon from the softener compartment and the coloured insert for liquid detergent). Replace the parts and refit the detergent dispenser. Insert the detergent dispenser in the washing machine. Mesh Filters in the Water Connection Check and clean regularly. For washing machines with a straight inlet hose 1. Turn off the tap and unscrew the water inlet hose from the tap. Clean the internal mesh filter and screw the water inlet hose back onto the tap. Now unscrew the inlet hose on the rear of the washing machine. Pull off the mesh filter from the washing machine connection with universal pliers and clean it. Refit the mesh filter and screw the inlet hose on again. Turn on the tap and ensure that the connections are completely water-tight. For washing machines with Water Stop hose 1. Turn off the tap and unscrew the Water Stop hose from the tap. Clean the internal mesh filter and screw the water inlet hose back onto the tap. Turn on the tap and ensure that the connection is completely water-tight. 13 Black Process Plate 4gb15170. fm5 Page 14 Thursday, July 11, 2002 11:35 AM Troubleshooting Guide Depending on the model, your washing machine is equipped with various automatic safety functions. This enables faults to be detected in good time and the safety system can react appropriately. These faults are frequently so minor that they can be removed within a few minutes. The washing machine stops during the programme (varies depending on model). Check whether: • the “Rinse Hold” light flashes, or the “Rinse Hold” button has been pressed; terminate this special option by pressing the button • another programme has been selected and the “Start/Pause” button is flashing. Reselect the desired programme and press the “Start/Pause” button • the door has been opened and the “Start/Pause” light is flashing. Close the door and press the “Start/Pause” button again • the “On/Off” button has been pressed and the light is on • the washing machine safety system has been activated (see “Fault Indicators” table) The washing machine vibrates during the spin cycle. Check whether: • the washing machine is level and standing firmly on all four feet • the transport bolts have been removed. [. . . ] Turn the water tap on (if water immediately flows into the appliance again, without the appliance being started, there is a fault. Turn off the tap and notify After-Sales Service). For models with fault display, select and start the desired programme again. For models with no fault display, continue the programme by pressing the “On/Off” button again. [. . . ]