User manual WHIRLPOOL WAL 9990 PROGRAM CHART

[. . . ] + 6. 0 ❉ Yes ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ 20 to 95 “Prewash” can be additionally selected for heavily soiled laundry at any temperature. “Prewash” can be additionally selected for heavily soiled laundry. Easy Care 2. 5 ❉ Yes ❉ ❉ ❉ ❉ ❉ ❉ 1) ❉ ❉ 20 to 60 1000 1) Daily Load Delicates Wool 3. 0 1. 5 1, 0 ❉ ❉ ❉ ❉ Yes Yes Yes – ❉ ❉ ❉ ❉ ❉ – ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ 1) ❉ 1) ❉ ❉ – – – – – – – – – 30 to 60 1600 – – If you select “Rinse Hold” do not leave items to soak for too long. – – – – ❉ – – – – – – – – 20 to 40 1000 1) 20 to 40 1000 1) – – – – – – – – – – – – – – Rapid Plus 3. 0 Yes 20 to 60 1600 – Handwash 1. 0 ❉ ❉ Yes ❉ ❉ ❉ ❉ ❉ ❉ ❉ 2) ❉ ❉ ❉ 1) 20 to 30 Rinse & Spin Intensive Spin – – – – – – – – 6. 0 6. 0 – – – – 20 If you select “Rinse Hold” do not leave items to soak for too long. A 400 2) very gentle spin is used in this programme. Same as the spin cycle in the “Cotton” 1600 programme. [. . . ] This is not possible if “Rapid Plus” is selected. * Consumption values were measured in normal conditions in compliance with Standard IEC/EN 60456. ** The programme duration may vary from the chart values. The washing machine will allow for individual household conditions and adapt the programme run time accordingly. *** To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out. • A list of all the available wash programmes appears in the LCD. Select the desired programme with “ ” and “ ” and confirm with “OK”. • You can then, as already described, select available additional options for the wash programme and set temperature and spin speed as desired. • When all the settings have been made and confirmed with “OK”, the programme is stored in the selected storage space and can be reselected at any time and run using “Start/Pause”. PROGRAMME END • The time remaining on the LCD shows 0:00, and displays “END OF CYCLE”. Turn the programme selector with the marking to the top. Open the door and unload the machine. POUR IN DETERGENT, CLOSE THE DOOR AND SELECT A PROGRAMME Add the detergent as described in the chapter “Detergent and Additives” in the booklet. Turn the programme selector knob in any direction to the desired programme. This appears in the LCD display, together with spin speed, wash temperature and wash programme duration (in hours and minutes). The indicator light above the “Start/Pause” button will blink. Temperature and spin speed can be changed using the “ ” button as well as the “ ” and “ ” buttons. The additional options available for the wash programme can be selected with the “ ” button. “Prewash” • Only for heavily soiled laundry (for example sand or granular dirt). Programme duration is increased by some 15 min. RESELECT AFTER PROGRAMME START A newly-selected programme will continue in the same programme section during which the current programme was interrupted. Therefore do not add any more detergent. Press the “Start/Pause” button to interrupt the programme. Select the new programme (with temperature), any additional options and - if you wish - another spin speed. In this way you can also select an additional option later, without changing the current programme. Press the “Start/Pause” button again to re-start the programme. [. . . ] • If the spin speed “0” is selected, the final spin is cancelled. The water is drained out only. “Start Delay” correction. • If you have already confirmed the desired start time with “OK” or have already pressed “Start/Pause”, they can still be changed. To do this, press the “Start Delay” button again. The set time blinks and can be changed with the “ ” and “ ” buttons. [. . . ]