User manual WHIRLPOOL WLMG 1010 INSTRUCTION FOR USE

[. . . ] Appliance The appliance is made using recyclable materials. Disposal must be carried out in accordance with local environmental regulations for waste disposal. Make the appliance unusable by cutting off the power cord. The appliance must be delivered to an authorised collection centre for the recovery of refrigerant gas. [. . . ] Bottle racks must be made from wood as this effectively absorbs any vibrations and keeps bottles away from the wall transmitting heat or cold. In addition, the bottles of wine must be stored away from substances or places with strong odours which can be easily absorbed by the wine. To this end, your new appliance has an active carbon filter to absorb any impurities in the air. Temperature and humidity Temperature is a critical and vital factor during the entire life cycle of wine; it determines how well the wine develops when matured in the bottle. To ensure optimal storage, the temperature must be kept constant from 8 to 12 °C. Rapid, wide temperature swings must be avoided: when the temperature is too high, the liquids dilate accelerating the ageing process whereas excessively low temperatures (below 4 - 5 °C) can cause the precipitation of tartrates; such an imperfection would impair the pleasant appearance of the wine. In the extreme event that the temperature drops below 0 °C, the wine would freeze causing the cork to explode. Humidity is also crucial in optimal wine storage: dry environments cause the cork to shrink whereas overly damp locations cause mould and harmful microorganisms to form. Humidity must be kept between 50% - 70%. Storage location Not everyone has a basement suitable for use as a cellar. Technology has only recently come up with an effective substitute for a natural cellar. Your new wine cellar is a special appliance designed specifically to hold and store wines properly. Indeed, it should only be used for your favourite bottles of wine, not for fruit, vegetables and tins. In this way, you can store and age any kind of wine properly even if you don't have a natural wine cellar. The cork This is an essential part of the bottle: the quality of the cork, selected by the wine-maker, is very important in the ageing process of the wine itself. The conditions of the cork, including corks in bottled wine, depend solely on the process and storage standards used by the manufacturer or bottler. How to store wine When storing your wine bottles, one golden rule not to be overlooked is that they must be laid horizontally or at an angle to ensure the wine keeps the cork wet. Some say that this causes the classic smell of “cork” in wine. In actual fact, keeping the cork in contact with the wine enhances its elasticity thereby guaranteeing its continued effectiveness. Another important factor in storing wine is how the bottles are arranged: the bottles should be 15 41133001GB. fm Page 16 Thursday, October 28, 2004 12:07 PM HOW TO USE THE WINE CELLAR Switching on the appliance Starting up the appliance All controls are on the outside of the appliance. Plug in the appliance to start it running and set the thermostat (Figure A1) to the required temperature; a green indicator light will come on (Figure A2) showing the appliance is on. An interior light (Figure B1) comes on automatically when the door is opened or can be switched on as required from the control panel (Figure A3). When faulty or broken, request a replacement from our authorized personnel (After-sales Service) Thermometer (Figure B2): A digital thermometer is provided along with the appliance and can be found inside the bag with the advertising materials. When attached to one of the wooden racks inside the cellar, the thermometer will display the interior temperature. The thermometer itself has a button cell battery which must be replaced when necessary. Adjusting the temperature 1. To ensure the appliance functions correctly, set the thermostat as explained in section “Introduction to wine” (page 15). [. . . ] • If the plug and socket are not of the same type, have the socket replaced by a qualified electrician. • Do not use extension leads or adapters. Disconnecting the appliance It must be possible to disconnect the appliance by unplugging it or by means of a two-pole switch fitted upline of the socket. 19 41133001GB. fm Page 20 Thursday, October 28, 2004 12:07 PM ELECTRICAL CONNECTION For Great Britain only Warning - this appliance must be earthed Fuse replacement If the mains lead of this appliance is fitted with a BS 1363A 13amp fused plug, to change a fuse in this type of plug use an A. S. T. A. approved fuse to BS 1362 type and proceed as follows: 1. Fit replacement 13A fuse into fuse cover. [. . . ]