User manual WHIRLPOOL WP 73/1 IX PRODUCT FICHE

[. . . ] Warning: when the door is opened steam comes out!Unload the appliance, starting from the lower rack. Switch off the appliance Turn off the water tap, unload the racks Dishwasher loading instructions and racks provided depending on the model Upper rack: Crockery holder (A): Depending on the position, for long-handles utensils, cups and plates. carving forks, knives) must be arranged with the sharp end facing in towards the appliance. B A C D Half Load: Load the upper rack (see description of Options). Place the cutlery basket (C), if provided, in the upper rack. Rack height adjustment (also when loaded): Pull the two rack handles (D) outwards and lower the rack. [. . . ] Lower adjustment: D Retainer open Retainer closed Removing the top rack to provide clearance for large items of crockery in the bottom rack: Open the rack guide retainers (E) on the right and left and remove the top rack. When the upper rack is in place the retainers must always be closed. E E Lower rack: Depending on the model with fixed or tilting plate holders (F). Half Load: Load the lower rack (see description of Options). Greater washing power, particularly for plates and saucepans. F F Cutlery basket (G): Grid (H) to keep items separate. Sharp knives and forks that might cause injury must be placed in the cutlery basket with the sharp end facing downwards. H G C Only use dishwasher-proof crockery and dishes. Do not use the appliance for items not suitable for washing in a dishwasher, for example wooden items, aluminium, tin, hand-decorated crockery (unglazed), silver cutlery. What to do if. . . If a fault occurs, before contacting our After-Sales Service, make the following checks to try and remedy the problem (* see also the corresponding chapter in the user instructions). Problem The appliance is not working Cause • No water supply. • The appliance does not load sufficient water. • Open the tap. Remedy • Clean the water supply tap filter. • Ensure there are no kinks in the water hose. • • • • Insert the plug into the mains socket. Check the safety circuit breaker. • Starting the selected programme. • The programme can be set to “0” to start. Select a new programme and press the Start button again. If after carrying out the above checks the malfunction persists or appears again, turn the appliance off and turn off the water supply tap, then call our After-Sales Service (see guarantee). Before contacting our After-Sales Service, take note of the following: • The nature of the fault • The appliance type and model • The service code (the number indicated on the adhesive rating plate) inside the door on the right-hand side. Before using the dishwasher, read the user instructions! WP 75 Quick Reference Guide Options 3) Time and failure display Off button Programme selection button The selected programme is shown in the window of the display. Switches “on” when the dishwasher is operating. Switches off at the end of the programme. GB On button Indicates in hours the time remaining until the start of the wash cycle. Switches off when the programme starts and indicates the time remaining in hours and minutes. “F. . . . ” Identification of faults for service technician “Delayed start” button Start button The wash cycle can be programmed to start after 1 - 24 hours. With each successive touch of the button, the delayed start indicator increases by 1 hour, and after 24 returns to 00. The dishwasher will start at the set time. “Half load” button The half load cycle can be used for the upper and lower rack. Select the required programme then press the “Half Load” button. The light comes on and goes off at the end of the programme. [. . . ] The “Half Load” function can be used with programmes marked with an (*). After pressing the Reset button, the selected programme and the supplementary functions are cancelled (except the detergent and water hardness settings, see user instructions) and must be reset. On releasing the button this is confirmed by an acoustic signal. Reset button Antibacterial rinse 4) 5) This function adds an antibacterial rinse at the end of the wash cycle, thereby guaranteeing a perfectly clean and sanitized load. The lamp will light up when the function is activated. If the temperature is not maintained during the antibacterial cycle (e. g. [. . . ]