User manual WHIRLPOOL WP 76 INSTRUCTION FOR USE

[. . . ] Detailed instructions are given in chapter 5 “What to do if. . . ”. Salt level indicator and rinse aid level indicator These indicator lamps light up when salt or rinse aid need to be added. Only add just before starting a wash cycle. Fault indication and wash time display In normal operation it indicates the remaining time (h:mm), whereas with “Delayed start” selected it indicates the time remaining until programme start (hh). [. . . ] How to check the rinse aid level Check the visual indicator C on the rinse aid dispenser: dark = sufficient rinse aid, clear = add rinse aid. In the case of appliances with an electric indicator on the Indicator C control panel, the rinse aid indicator lamp lights up red when rinse aid needs to be added. How to fill the rinse aid dispenser max Open the rinse aid dispenser by pressing the right button (button 2) of the dispenser. Fill the dispenser with rinse aid up to the “max” line (approx. Only use rinse aids recommended for use in domestic dishwashers. Immediately wipe away any rinse aid spilt accidentally. This prevents the formation of excess suds which can cause a fault function of the appliance. How to adjust the rinse aid dosage regulator The rinse aid dosage can be adjusted to the detergent used. The lower the setting, the less rinse aid is dispensed (factory setting: position 4). Using a coin or similar object, turn the arrow to the desired setting. After adjusting the rinse aid setting, shut the cover again. - The appliance must be switched off to memorise the new setting. Water hardness 1 soft 1 - 2 medium 2 medium 3 medium-hard 4 hard 4 very hard 4 extremely hard German degrees °dH 0-5 6 - 10 11 - 15 16 - 21 22 - 28 29 - 35 36 - 60 French degrees °fH 0-9 10 - 18 19 - 27 28 - 37 38 - 50 51 - 63 64 - 107 English degrees °eH 0 - 6. 3 7 - 12. 6 13. 3 - 18. 9 19. 6 - 25. 9 26. 6 - 35 35. 7 - 44. 1 44. 8 - 74. 9 Flashing frequency or display setting 1 / 1x 2 / 2x 3 / 3x 4 / 4x 5 / 5x 6 / 6x 7 / 7x Water hardness level is factory set at 3 for medium-hard water (display 4 or 4 flashes of the START button). Water hardness level 4 with combined action detergent Even if you use a combined action detergent which includes salt, you must still add regeneration salt since such detergents are not effective enough at softening hard water. If the appliance is equipped with the function “Select detergent” (see chapter “1. Overview”), set the detergent dispenser system to the “no salt” setting so that the salt indicator lamp remains activated (“Detergent with rinse aid”). PRECAUTIONS AND GENERAL RECOMMENDATIONS 1. Packing The packaging materials are 100% recyclable and marked with the recycling symbol. Removing the packaging and inspecting the contents After unpacking, make sure that the dishwasher is undamaged and that the door closes correctly. If in doubt, contact a qualified technician or your local retailer. Before using the dishwasher for the first time - The appliance is designed to operate at ambient temperatures of between 5°C and 45°C. - This dishwasher has been tested by the manufacturer to ensure it functions correctly. Such testing may leave slight drips/ water marks which will disappear with the first wash. [. . . ] bowls, cups) must be arranged facing downwards in the rack. If necessary, use more detergent, observing the manufacturer’s indications as regards dosage. Always store detergent in a dry place and do not store it for excessively long periods of time. For heavily soiled crockery, select a wash programme with a higher temperature (see table 1. 1 on the first page). [. . . ]