User manual WHIRLPOOL WP 85 PROGRAM CHART

[. . . ] Before using the dishwasher, read the installation and maintenance instructions carefully! GB WP 85 1. OVERVIEW ON button Programme selection button Press the button repeatedly until the desired programme indicator lights up. START button The indicator lights up during operation, flashes when a fault occurs, and goes off at the end of the programme. START button RESET function: Press this button for at least 2 seconds; the selected programme and options are cancelled. [. . . ] How to set the water hardness level - Switch on the appliance. - Select the 2nd programme “P2” - consult the table 1. 1 in chapter 1. - Press the START button for at least 5 seconds until the START indicator lamp flashes. - The set water hardness level is shown on the display (if present) or the START button flashes. - With each successive touch of the START button the setting increases and when it reaches 7 it returns to 1 again. - The appliance must be switched off to memorise the new setting. Water hardness 1 soft 1 - 2 medium 2 medium 3 medium-hard 4 hard 4 very hard 4 extremely hard German degrees °dH 0-5 6 - 10 11 - 15 16 - 21 22 - 28 29 - 35 36 - 60 French degrees °fH 0-9 10 - 18 19 - 27 28 - 37 38 - 50 51 - 63 64 - 107 English degrees °eH 0 - 6. 3 7 - 12. 6 13. 3 - 18. 9 19. 6 - 25. 9 26. 6 - 35 35. 7 - 44. 1 44. 8 - 74. 9 Flashing frequency or display setting 1 / 1x 2 / 2x 3 / 3x 4 / 4x 5 / 5x 6 / 6x 7 / 7x Water hardness level is factory set at 3 for medium-hard water (display 4 or 4 flashes of the START button). Water hardness level 4 with combined action detergent Even if you use a combined action detergent which includes salt, you must still add regeneration salt since such detergents are not effective enough at softening hard water. If the appliance is equipped with the function “Select detergent” (see chapter “1. To load crockery, open the door with caution: beware of hot steam. The programme resumes the cycle from where it was interrupted. The wash cycle can be interrupted at any time by pressing RESET. Changing the programme in progress/Resetting - Press the START button for about 2 seconds, until the START indicator lamp switches off. - The appliance is now ready to be restarted. Full integrated models - Press the START/RESET button (for 2 seconds). - The appliance is now ready to be restarted. PROGRAMME END Exercise caution when opening the door: beware of hot steam. Only press the OFF button once the START indicator lamp has switched off. Unload the appliance, starting from the lower rack in order to avoid any residual drips of water falling onto crockery below. For even better drying results, leave the dishwasher door open a little before unloading in order to allow the steam to dissipate, helping the dishes to dry. The underside of the kitchen worktop must be protected (see instructions in “Maintenance and Installation”). 5 4. PRECAUTIONS AND GENERAL RECOMMENDATIONS 1. Packing The packaging materials are 100% recyclable and marked with the recycling symbol. Removing the packaging and inspecting the contents After unpacking, make sure that the dishwasher is undamaged and that the door closes correctly. If in doubt, contact a qualified technician or your local retailer. [. . . ] If you select the “Half load/Multizone” function (if available), remember to load only the upper rack or only the lower rack to increase washing power and thus obtain optimum wash results. WHAT TO DO IF. . . Crockery and cutlery . . . . . . are not perfectly clean/have food residues Possible causes/solutions . . . have deposits: - regeneration salt residue - rust marks In the event of frequent use of low temperature programmes (50°C or lower) (if available), every now and again select a higher temperature programme The spray arms must not be clogged, the filters must not be dirty and must be fitted correctly (see the instructions in “Maintenance and installation”). The spray arms must be able to turn freely and must not be impeded by crockery or cutlery. [. . . ]