User manual WHIRLPOOL WRF560SEYM DIMENSION GUIDE

[. . . ] 8 Start Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Component Description . 20 Removal and Replacement Reservoir and Bin Controls . 31 Parts lists and wiring diagrams are in the center of this manual, printed on yellow paper. October, 1991 Page 1 WRF560SEYM FOR THE INSTALLER BACK VIEW: AIR COOLED Note: Allow 6" behind and 6" above either unit for air circulation, utility connections, and service. ELECTRICAL INLET BACK VIEW: WATER COOLED ELECTRICAL INLET WATER INLET 9. 5" 5. 25" 3" 5. 25" 3" 7. 3" 9. 43" WATER INLET 3/8" FLARE DRAIN 3/4" FPT Condenser Inlet 3/8" FPT 2. 1" 5. 7" 2. 9" Condenser Drain 1/2" FPT 3. 4" DRAIN 3/4" FPT 4. 9" 7. 46" The WRF560SEYM is designed to fit the following Scotsman storage bins: B590 and extensions (with bin top KBT18) BH800 using bin top KBT15 (one unit). [. . . ] Clean the condenser: the condenser may appear to be clean on the surface, but it can still be clogged internally. Check with a flash light from the front to see if light can be seen though the condenser fins. Reverse to reassemble. Step 2: Remove two screws and Step 4: Clean the condenser. October, 1991 Page 18 WRF560SEYM MAINTENANCE AND CLEANING: Auger In some areas, the water supply to the ice maker will contain a high concentration of minerals, and that will result in an evaporator ALLEN and auger becoming coated with these SCREWS minerals, requiring a more frequent removal /////////////WARNING/////////////// The auger has sharp than twice per year. If in doubt about the edges, handle with care. condition of the evaporator and auger, the auger can be removed so the parts can be //////////////////////////////////////////// inspected. Note: Water filters can filter out suspended BREAKER & BEARING & solids, but not dissolved solids. "Soft" water AUGER may not be the complete answer. Check with ASSEMBLY a water treatment specialist regarding water treatment. For more information on removal of these parts, see REMOVAL AND REPLACEMENT. //////////////////////////////WARNING//////////////////////////// 6. If the pressures are still too high replace the water regulating valve. Check for adequate air flow on air cooled. Clean the condenser and (if used) the filter. If the air flow is poor because of the installation, advise the user that the unit should be moved, or the air around it kept cooler. Check the fan motor for tight bearings and proper rotation. Check that the fan blades are clean, and the fan secure to the fan motor shaft. Check the spout switch (a manual reset). It opens from excess pressure of ice inside the ice chute: this should only happen when the machine does not shut off when the ice storage bin is full. On units older than July, 1990 production, this switch will reset when the ice melts, but the machine will not resart until the reset switch on the circuit board is pressed. The machine will not run if there is not enough water in the reservoir. See the next step. October, 1991 Page 20 WRF560SEYM SERVICE DIAGNOSIS: Condition - No Ice Being Produced STATUS: NOTHING OPERATES H. [. . . ] D) After replacing parts as required, (if any) reassemble the gearcase. The two smaller gears and the oil should be in the lower case, the output gear will be with the cover. As you lower the cover onto the lower case, the cover will have to be moved closer to the second gear after WATER SHED CENTRIFUGAL SWITCH SEAL AUGER DRIVE MOTOR ROTOR BEARING SEAL the output gear has cleared the second gear top bearing. E) After the case is together, and the locating pins are secure in both ends, replace all cap screws. [. . . ]