User manual WHIRLPOOL WRF736SDAW DIMENSION GUIDE

[. . . ] Type Minimum Circuit Ampacity Remote Air 14. 1 Remote Air 11. 2 Remote Air 14. 1 Remote Air 11. 2 Maximum Fuse Size 20 15 20 15 Refrigerant Charge (R-404A) 208 ounces 208 ounces 208 ounces 208 ounces 208-230/60/1 203-230/60/1 208-230/60/1 208-230/60/3 FLAKE FLAKE NUGGET NUGGET Minimum Circuit Ampacity is used to determine wire size and type per National Electric Code. January 2005 Page 2 Installation Limitations: This ice system is designed to be installed indoors, Scotsman Ice Systems are designed and in a controlled environment: manufactured with the highest regard for safety and performance. Air Temperature 50 F 100 F 0 0 Scotsman assumes no liability or responsibility of Water Temperature 40 F 100 F any kind for products manufactured by Scotsman Water Pressure 20 psi 80 psi that have been altered in any way, including the Voltage 5% +10% use of any part and/or other components not (Compared to the nameplate) specifically approved by Scotsman. The temperature limitations do not apply to the Scotsman reserves the right to make design remote condenser. It will work between -20 changes and/or improvements at any time. [. . . ] It is the USER'S RESPONSIBILITY to see that the unit is properly maintained. It is always preferable, and less costly in the long run, to avoid possible down time by keeping it clean; adjusting it as needed; and by replacing worn parts before they can cause failure. The following is a list of recommended maintenance that will help keep the machine running with a minimum of problems. Maintenance and Cleaning should be scheduled at a minimum of twice per year. Electrical power will be ON when doing in place cleaning. Check and clean any water treatment devices, if any are installed. Remove all the ice from the storage bin. Remove the cover to the water reservoir and block the float up. Drain the water reservoir and freezer assembly using the drain tube attached to the freezer water inlet. Return the drain tube to its normal upright position and replace the end cap. Prepare the cleaning solution: Mix eight ounces of Scotsman Ice Machine Cleaner with three quarts of hot water. Switch the machine Off and check the bearing: ·unscrewing the auger stud Auger Stud ·removing the ice chute cover Chute Cover Cap Screw ·unscrewing the ice sweep Ice Sweep Inspect the bearing. There should be plenty of grease in sight. If grease is needed the bearing and breaker should be removed to check the action of the bearing. To remove the breaker remove the lower ice chute then take out all four allen head cap screws and pull the breaker off the auger and evaporator. If the bearing only needs grease, inject grease into the bearing using Scotsman grease needle pn 02-3559-01 and Scotsman bearing grease cartridge, pn A36808-001. Be sure to inject grease evenly and thoroughly. Bearing Needle, pn 02-3559-01 ·removing the water shed & unscrewing the breaker cover (left hand threads). Breaker Cover Off See Removal and Replacement section to replace bearing or seals. Reverse to reassemble. January 2000 Page 22 AUGER MAINTENANCE NME1254R & WRF736SDAW Note. Water filters can filter out suspended solids, but not dissolved solids. "Soft" water may not be the complete answer. Check with a water treatment specialist regarding water treatment. For more information on removal of these parts, see REMOVAL AND REPLACEMENT. [. . . ] Remove the electrical wires from the gear drive motor. Unscrew the 4 cap screws holding the gearmotor to the gearmotor plate. COVER A) Remove the cap screws holding the gearmotor case halves together and pry the two cases apart. B) To lift off the cover, lift up until you can feel internal contact, then pull the cover towards the output gear end, and then lift the cover (with drive motor attached) up and away from the gear motor case. [. . . ]