User manual WHIRLPOOL WRS342FIAM WARRANTY INFORMATION

[. . . ] All other charges, including transportation charges for replacements under this warranty and labor costs not specifically covered by this warranty, shall be borne by you. This warranty is extended only to the original purchaser of the U-Line product. The Registration Card included with the product should be promptly completed by you and mailed back to U-Line or you can register on-line at www. U-LineService. com. The following are excluded from this limited warranty: installation charges; damages caused by disasters or acts of God, such as fire, floods, wind and lightening; damages incurred or resulting from shipping, improper installation, unauthorized modification, or misuse/abuse of the product; customer education calls; food loss/spoilage; door and water level adjustments (except during the first 90 days from the date of purchase); defrosting the product; adjusting the controls; door reversal; or cleaning the condenser. [. . . ] Figure 24 16 6. 7. UL128 8. Install bottom hinge on cabinet, opposite side, aligning flat edge of hinge with outer edge of unit. Relocate plastic spacer/ bushing on bottom of door to opposite side, and place door on bottom hinge pin (see Figure 20). Clean out bushing hole in door bottom with a screwdriver if needed. Align flat edge of top hinge with outer edge of unit and fasten upper hinge to unit (4 screws). Partially tighten screws until door is aligned. Tighten upper and lower hinge screws securely. Replace four plastic plugs removed in step 5 into holes on top of unit. Replace screws in holes in bottom of unit, opposite side. Reinstall grille (1 screw). 17 User's Manual REVERSING A STAINLESS STEEL DOOR Stainless Steel models are field reversible for left or right hand opening. The door opening is easily reversed by moving the hinge hardware to the opposite side (see Figure 26) as follows: 1. Remove the bottom hinge (2 screws) from door. Pull handle up and off. Figure 29 5. UL132 Figure 30 20 NOTE Use care not to bend light switch bracket (where installed), located on door bottom when installing door insert. Do not set door on bottom edge when pushing insert into place. Slide custom door panel insert into 1/4 inch channel in door front. Holding door gasket out of the way, replace handle on door making sure it is seated properly on insert and that screw holes line up. Install two small screws removed in step 4. Starting at the center and working outward, push door gasket into place on door. 8. Place door on bottom hinge pin and install upper hinge screw (see Figure 28). Adjust if needed. BUILT-IN INSTALLATION Your U-Line product has been designed for either free-standing or builtin installation. When built-in, your U-Line product does not require additional air space for top, sides, or rear. However, the front grille must NOT be obstructed. NOTE Combo Models 29A, 29FF, and 75A require additional clearance when the door opens from the right (see Figures 32 and 33). This additional clearance allows for the ice bucket to be removed from the unit. Unit Dimensions Model SP18 95 98 15 Series 29 Series 75 Series Width 13-15/16" 13-13/16" 14-13/16" 14-15/16" 20-13/16" 23-7/8" Height 18-1/2" 24-3/4" 27-3/8" 34 - 35" 28-1/2" 34 - 35" Depth 25-1/4" 17" 20" 23-3/4" 24" 24" 21 User's Manual NOTE To ease unit installation and removal, increase the Unit Dimension measurements. [. . . ] Leave water supply line and power cord disconnected until ready to reuse. NOTE The use of anti-freeze or other products of this nature is not necessary and is not recommended. 30 TROUBLESHOOTING BEFORE CALLING FOR SERVICE If the unit appears to be malfunctioning, read through NORMAL OPERATION first. If the problem persists, check the TROUBLESHOOTING GUIDE. Locate the problem in the guide and refer to the cause and its remedy before calling for service. The problem could be something very simple which can be solved without a service call. TROUBLESHOOTING GUIDE ! [. . . ]