User manual WHISPER CREEK ARCHERY COMPOUND BOW 2005

[. . . ] 2005 Compound Bow Owner's Manual Table of Contents Whisper Creek Mission Bow Terminology Safety Instructions Care Instructions Cam Performance Draw Length Adjustments Let-Off Adjustments Draw Weight Adjustments Bow Press Instructions Proofs of Technology Whisper Creek Technology 3 4 5 6 7 9 11 11 12 13 15 WHAT SETS US APART We can assure you that no other bow company has the technology that Whisper Creek Archery has. Whisper Creek Archery is light-years ahead of others when comparing to "Compound Bow" Technology. Our mission at Whisper Creek Archery is to provide you with the highest quality and most technologically advanced bow in the industry. Through extensive research and development, our technology provides the archer with the quietness, precision, speed, and versatility that are needed to perform the job well. [. . . ] Each module will give you only 1" draw adjustments. (WARNING: always make sure that you use blue loc-tite or teflon tape when replacing modules and tighten fasteners securely). Control Cable Post LOWER CAM Modules Cam Indicator Marks UPPER CAM Cam Modules CounterFORCESolo Please note the following instructions in order to properly utilize the draw modules within the CounterFORCESolo System when changing draw lengths. Your draw weight will not change from module to module. Draw length adjustments in 1" increments. To change out the module, place the bow into a bow press (WARNING: strings MUST be relaxed in order to change out the draw modules), and remove the fasteners. Replace the new module into the designated slot as noted on the cam by slightly pulling up on the module where noted in figure (WARNING: Do not over bend module where module will not flex back into position) and fasten the module to the cam. Note that it is IMPORTANT that the cleats be seated into position prior to fastening. (WARNING: always make sure that you use blue loc-tite when replacing modules and tighten fasteners securely). CounterFORCE cps& 1/2 The Whisper Creek CPS & 1/2 system has a range of 5 1/2 inch draw length adjustment using 3 inter-changeable draw modules. Each draw module, numbered 1 through 3, has a full 1 1/2 inches of draw length adjustment. Adjustments can be made in 1/8" increments using the string anchor post on the control wheel (top, or 1/2" increments using the sliding modular on the power cam (bottom). An exact draw length can be achieved using a combination of these methods. A bow press must be used to adjust the modular and the string anchor post. SLIDING MODULAR The CPS modular is located on the power cam. It can be adjusted by removing both flathead screws and sliding the modular from position 1 through 4 (position one being the shortest draw and 4 being the longest). Once in position, tighten the screws back into the module. A full inch of adjustment in 1/2-inch increments can be obtained this way. STRING ANCHOR POST The string anchor post can be found on the control wheel. Remove the flat head screw and slide the post to the desired position A through D (position A being the shortest and D being the longest). Once in position, tighten the screw back onto the string anchor post. This system is so efficient that no stabilizer and/or limb damping accessories are needed. We absolutely guarantee no vibration (twang) within the PS (BowACTUATORTM Suspension Technology) Series type bows. In order to prove this claim, a simple test can be performed: Steps To Prove How Technology Works: 1. Take a Stealth "bare" with only string leeches on the string. Take a Stealth "loaded" with a stabilizer, Limb LimbSavers, cable rod LimbSavers, and string leeches on the string. [. . . ] The BowDAMPTM Material will not swell or deteriorate in water where most plastics and/or elastomers will. BowDAMPTM Material Technology was designed to resist high impact as well as having "outstanding" abrasive resistance. Its abrasive resistance is about 20 times better than that of steel - that's right steel!It is also known for its toughness and durability. [. . . ]