User manual WHISTLER PRO-1200W

[. . . ] The new arsenal they carry is called POPTM Mode. This new gun is a normal K or Ka band radar gun detectable by most radar detectors made in the past 30 years, unless the gun is placed in POPTM Mode. POPTM Mode is a feature on some newer radar guns operating on K and Ka bands. When the gun is in POPTM Mode and activated, a brief burst of energy, less that 1/15 of a second, is transmitted and the vehicle's speed is quickly acquired. [. . . ] · Press and hold Dark for 2 seconds until unit beeps once then release. Display switches: to If Temperature or Battery Voltage is programmed (see Option Select Mode), pressing and holding Dark for 2 seconds will momentarily switch to the other reading. Example: to See Option Select Mode on page 13 to change display viewing. · Vertically 10 11 Pro-3450_OwnersManual. qxd 3/15/04 4:30 PM Page 15 OPERATION Stay AlertTM Feature The Stay AlertTM Feature is designed to test a driver's alertness. To engage (when unit is not alarming): · Press and hold City for 2 seconds. Display reads: OPERATION Option Select Mode Entering Option Select Mode allows you to customize options such as Tone Select, Real Voice®, Abbreviated Power Up Sequence test and VG-2 Mode. When selecting options, Dark (D)=yes, City (C)=no, Quiet (Q)=next selection. Any one of these must be pressed within 20 seconds or options mode will automatically be exited. To enter: Press Q: *Display To Change, Option: Reads: Reads: For 2 Seconds 2nd time 3rd time 4th time 5th time 6th time 7th time 8th time 9th time TONE 3 TEST YES TEMP °F TEMP NO BATT NO POP ON SR OFF X ON K ON D or C D = YES C = NO D or C D = YES C = NO D = YES C = NO D = YES C = NO D = ON C = OFF D = ON C = OFF D = ON C = OFF Tone1, Tone 2 X, K, Ka Audio tones 1 beep during Power Up Changes Temp Reading Temp ON Temp OFF Battery Voltage ON Battery Voltage OFF Turns POPTM Mode ON Turns POPTM Mode OFF Turns Safety Radar ON Turns Safety Radar OFF Turns X Band ON Turns X Band OFF Turns K Band ON Turns K Band OFF Within 30-60 seconds two beeps are sounded; to show alertness, the driver must press either the Dark, City or Quiet button within 3-5 seconds. If the button is pressed within 3-5 seconds, the cycle is repeated. If a button was not pressed within 3-5 seconds alarm sounds and the display reads: · Press P/V to exit. Stay AlertTM is NOT intended as a substitute for adequate rest. The display reads: If a R error occurs: · Press P/V to turn unit off. · Check connection in back of control panel. · Perform "reset features. " · See dealer/installer. If a T error occurs: · Press P/V to turn off unit. · Check connection in back of control panel. NOTE: This T error occurs only at Power Up. 18 19 Pro-3450_OwnersManual. qxd 3/15/04 4:30 PM Page 23 TROUBLESHOOTING GUIDE Your Whistler detector is expertly engineered and designed to exacting quality standards to provide you with reliable, trouble-free operation. If your unit has been correctly installed following the guidelines in this manual, but is not operating optimally, please refer to the troubleshooting guide below. PROBLEM: No display or audio. · Check fuse in power cable, replace if necessary. · Check fuse in fuse box, replace if necessary. · Make sure power cable is properly grounded. PROBLEM: Unit alarms when vehicle equipment or electrical accessories (brakes, power mirrors/windows, directionals, horn, etc. ) · Check conditions of vehicle's electrical system, including battery and alternator. [. . . ] Whistler is not liable for damages arising from the use, misuse, or operation of this product. NOTE: This warranty does not include installation or reinstallation charges. WARRANTY INFORMATION When returning a unit for service under warranty, please follow these instructions: 1. Ship both the control panel and antenna (CAUTION: DO NOT CUT WIRES when removing the antenna as this will void the warranty. ) in the original carton or in a suitable sturdy equivalent, fully insured, with return receipt requested to: Whistler Repair Dept. 72756 Please allow 3 weeks turnaround time. [. . . ]