User manual WIN ENTERPRISES 104 PLUS MODULE

[. . . ] PC/104-PLUS Module Model Number MB-73030 AMD Geode LX800 Low Power PC/104+ SBC with VGA/LCD, two 10/100LAN, Audio & SSD User's Manual Version 1. 0 1 Table of Contents Chapter 1. General Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Features and Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MB-73030 Packaging. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4. Board Layout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 3 The default space is available and optimized per the current onboard devices settings. Any change might cause conflict against the existing onboard devices. Be very careful when change anything here. LPC Card Devices Configuration: Use the LPC Card Devices Configuration as follows: 1. LPC Card Devices Configuration" from the Motherboard Device st Configuration menu. The following screen appears: This page is to configure the 1 LPC UART device. Use the arrow keys to move between fields. Modify the selected field using the +/- or <Enter> keys. Some fields let you enter numeric values directly. 26 Serial Port 1/2: to select port address & IRQ, the options are 3f8 IRQ4/ 2f8 IRQ3 Serial Port 2: IR Function Mode: Standard mode/ IrDA mode/ ASKIr mode IR I/O Pin Location Select: SINB/ SOUTB or IRRX/ IRTX IR Duplex Function Select: Full Duplex/ Half Duplex Parallel Port: 0378/ 0278/ 03BC/ Disabled Mode: Compatible/ PS/2 Bi-Direction/ EP1. 7/ EP1. 9/ ECP IRQ: IRQ7/ Disabled DMA: None/ Channel 3/ Channel 1 Console Redirection Configuration Console Output Setting: Disabled/ Enabled Baud Rate Setting: / 115200 After boot Enable or Disable Console ReDirection Agent after boot: Disabled/ Enabled 27 Use the Video and Flat Panel Configuration as follows: 1 Choose "F. Video and Flat Panel Configuration" from the Motherboard Device Configuration menu. The following screen appears: 2 Use the arrow keys to move between fields. Modify the selected field using the +/or <Enter> keys. Some fields let you enter numeric values directly. Internal Adaptor Mode: This is to choose the Internal Video controller mode when an external Video device is present. The options are: Primary/ Secondary/ Disabled Graphics Memory: to decide share video memory 2~254MB Driver controls init: Disabled/ Enabled, set Enabled when you want to use OS driver for Graphic Initialization. Output Display: Panel and CRT/ CRT/ Panel DOTPLL Bypass: Disabled/ Enabled, Use the frequency on DOTREF pin as dot clock frequency Flat Panel Configuration Type: TFT/ LVDS/ Auto ( auto detect the LCD type) Resolution: 320x240/ 640x480/ 800x600/ 1024x768/ 1152x864/ 1280x1024/ 1600x1200 Data Bus Type: 924 bits, 1 ppc/ 18, 24 bits, 2 ppc Refresh Rate: 60/ 70/ 72/ 75/ 85/ 90/ 100 Hz HSYNC Polarity: Active low/ Active high VSYNC Polarity: Active low/ Active high LP Active Period: Free running/ Active only SHFCLK Active Period: Free running/ Active only Software Backlight Control: Disabled/ Enabled Initial Brightness: Last value/ 0~100% 28 PCI Configuration: Use the PCI Configuration as follows: Choose "G. PCI Configuration" from the Motherboard Device Configuration menu. The following screen appears: Use the arrow keys to move between fields. Modify the selected field using the +/- or Enter> keys. Some fields let you enter numeric values directly. PCI Interrupt Steering: Enable/ Disable INTA# to IRQ Steering There is no PCI expansion slot available in this model, so there is no function here. USB 2. 0 Settings: OHCI: Enabled/ Disabled EHCI: Enables/ Disabled UDC: Disabled/ Enabled Over-current reporting: Disabled/ Enabled Use the Thermal Configuration as follows: 1 Choose "T. Thermal Configuration" from the Motherboard Device Configuration menu. The following screen appears: 2 Press <Enter> key here, it will read back the current temperature (Celsius) from System Monitor chip W83627HG and show. 29 2. Use the arrow keys to move between items and to select values. [. . . ] Press the <Y> key and then press <Enter> if you want to load the SETUP default. 36 3. 12 Supervisor/User Password The password options let you prevent unauthorized system boot-up or unauthorized use of CMOS setup. The Supervisor Password allows both system and CMOS Setup program access; the User Password allows access to the system and the CMOS Setup Utility main menu. The password functions are disabled by default. You can use these options to enable a password function or, if a password function is already enabled, change the password. [. . . ]