User manual X10 DS7000

[. . . ] Supervised Security System Owner's Manual 15 · · 1· 3 5 · RECORD Install Run 1 Run 2 13 11 · ·9· UNIT 7 ARM A· O· C · · BYPASS M · E · K I· G · HOUSE AC Power Battery Low zones 1 2 1 4 7 PROG 2 5 8 0 3 6 9 MEM REC/BUSY 3 4 5 6 7 8 ARMED Supervised Security System, Model DS7000 Contents READ THIS FIRST This equipment generates and uses radio frequency energy, and if not installed and used properly, that is, in strict accordance with the manufacturers instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for remote control security devices in accordance with the specifications in Sub-Parts B and C of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by unplugging the equipment, try to correct the interference by one or more of the following measures. [. . . ] Press PROG, enter fourth phone number, press MEM, 4. Repeat the above process to change a phone number. Modules A wide range of switch and control modules are available from X10, all of which can be controlled from the same remote controls which are used to operate the security system. Modules available include replacement wall switches, X10 controlled AC outlets, screw-in lamp modules, plug-in appliance modules and many others. Note: if you only want to program one phone number, you should store this number in all four memory locations. Storing a Voice Message 1. Speak clearly into the microphone on the front of the console. You can record up to 15 seconds of speech. For example: "There is a burglary in progress at (address). Press 0 to listen-in. " After 15 seconds the BUSY light turns off. Plug the earphone into the jack on the side of the console. The console plays back your message through the earphone so you can hear what it sounds like (it sounds better when played back over the telephone line). If you want to hear the message again, set console to INSTALL then back to RUN. Repeat above steps to change the message. Remotes As well as being able to add up to 16 security remotes to the system, you can also add any number of Home Automation wireless remotes such as the handheld PalmPadTM remote which controls up to 16 modules around the home. Controllers A range of plug-in controllers are available including the Mini Timer which controls up to four modules with two on/off times each day, the Touch-Tone Controller which lets you use any touch tone telephone to call home and control X10 modules, and products which allow any WindowsTM based PC to control X10 Modules. Special products For special installation requirements a range of accessory products are available including powerline filters for multiple installations in close proximity, RF and powerline repeaters for larger installations and interface modules to tie-in X10 control with third party security products. 14 15 Using the Security System Console Zone Indicators The console displays the status of the first eight zones. These indicators can display four states, as follows: Steady on - means that particular door or window is open. Steady off - means that particular door or window is closed. Slow Flashing - means that particular Door/Window Sensor or Motion Detector is reporting a problem, low battery for example. Fast Flashing - means that particular Door/Window Sensor or Motion Detector reported a problem and the fault was bypassed, or the door or window is open and has been bypassed. Battery Light - Indicates battery in the Console is low and needs replacing. Armed Light - Indicates the unit is armed and ready to activate. All Door/Window Sensors and Motion Detectors report in to the Console every 90 minutes. If the Console does not receive a signal from the sensor within four hours, it reports a problem with that sensor by slowly flashing the appropriate zone indicator. If you try to arm the system with a zone indicator flashing, the Console sounds a repetitive trouble alarm. Either press DISARM, correct the problem and press ARM again, or press BYPASS while the trouble alarm is sounding, then press ARM. The zone(s) with a problem will not be armed and the zone indicator(s) will flash rapidly. [. . . ] If not: · Check that the console's slide switch is set to INSTALL. · Change the code on the sensor/motion detector (see Setting Up Door/Window Sensors and Setting Up Motion Detectors. PROBLEM If the armed indicator is flashing. SOLUTION This indicates that there has been an intrusion. Also, if a zone indicator is on, this indicates which zone was violated. To turn the zone indicator off, and stop the armed indicator from flashing press ARM then DISARM on the remote control. [. . . ]